Filter
Top Products
19
2
Chapter 2 Parts and their Functions (continued)
2-7 Warning and Status Display
Functions
Back tally lamp
When the BACK TALLY switch is set to [ON], the
lamp behaves in the same way as the front tally lamp at
the viewfinder.
BACK TALLY switch
This switch controls the action of the back and
rear tally lamps.
ON: Back and rear tally lamps enabled.
OFF: Back and rear tally lamps disabled.
WARNING lamp
This lamp starts blinking or lights up if something
unusual occurs in the memory.
LIGHT button
Use this button to control illumination of the display
window.
Alternately pressing this button toggles illumination of
the display window on or off.
Display window
This window displays warnings, battery-remaining level,
sound volume, time data, and other information.
Rear tally lamp
When the BACK TALLY switch is set on [ON], the
rear tally lamp behaves in the same way as the back
tally lamp.
2-8 Display Window Functions
P2 card/battery-remaining level indications
Memory action status indication
Error Code Indication (for more information, see
[7-3 Warning System])
LOOP
h
MEDIA
E
F
Y minM
s
frm
13 24
0
D
VTCG
TIME DATE
P- REC
SLAVEHOLD W
BATT
EF
OVER OVER
10
OO
40
-dB
30
20
NDF
DV
DRIVE OP-SLOT
CTL
Battery-remaining level indication bar
For a battery with a digital indicator (percentage indication), if
the remaining level of the battery is higher than 70%, all
seven segments up to the “F” position are lit.
When the remaining level falls below 70%, the segments go
out one-by-one for each drop of 10%. All seven segments
can be set to light up when the battery-remaining balance is
100%. To do so select “100%” for the menu option BATT
REMAIN FULL in the <BATTERY/P2CARD> screen of the
MAIN OPERATION page.
Audio channel level meter
When the MONITOR SELECT CH1/2 / CH3/4 switch is set
to [CH1/2], the meter indicates 1 and 2 as the audio
channel numbers, together with their audio levels. When
the switch is set to [CH3/4], the meter indicates 3 and 4 as
the audio channel numbers, together with their audio levels.
Media-remaining space indication bar
The bar indicates the remaining free space on each P2 card,
using a seven-segment display.
Each segment can represent either three or five minutes of
remaining free space, depending on the value set through the
menu option CARD REMAIN/. According to the set value, the
segments disappear one-by-one. The menu option CARD
REMAIN / can be found in the <BATTERY/P2CARD> screen on
the MAIN OPERATION page.
LOOP
h
MEDIA
E
F
Y minM
s
frm
13 24
0
D
VTCG
TIME DATE
P- REC
SLAVEHOLD W
BATT
EF
OVER OVER
10
OO
40
-dB
30
20
NDF
DV
DRIVE OP-SLOT
CTL
Information indication
LOOP: Stays illuminated in LOOP REC mode. For
information about the LOOP REC mode, see [3-5
Loop Recording].
DRIVE: Stays illuminated when the menu option USB is set
to “ON”. The menu option USB can be found in the
<SYSTEM MODE> screen on the SYSTEM
SETTING page.
OP-SLOT: Remains illuminated when a video encoder card is
operated in the optional slot.
#,52%2'PINKUJDQQMࡍࠫ㧞㧜㧜㧡ᐕ㧝㧞㧤ᣣޓᧁᦐᣣޓඦᓟ㧝㧞ᤨ㧠㧥ಽ