Filter
Top Products
48
Chapter 4 Adjustments and Settings for Recording (continued)
Information Item Indication Status
Gain value
__dB Current gain value.
System information
and warnings
SYSTEM ERROR-__
TURN POWER OFF
CARD ERR _
REC WARNING
BACKUP BATT EMPTY
WIRELESS-RF
EOM
BOS
EOS
CANNOT REC
CANNOT PLAY
COMM ERROR
VOICE CANNOT REC
VOICE REC
VOICE OFF
VOICE PLAY
MARK ON/OFF
UPDATING
USB DRIVE
THUMBNAIL OPEN
1394 INITIAL ERROR
PROXY REC P2&SD
PROXY REC P2
NEAR END (SD)
EOM (SD)
PROXY CARD ERROR
SD CARD WRITE ERR
Something abnormal is happening to the internal computer communications
or reference signal. No further recording or playback can be performed. __is
replaced with an error code.For more information, see [7-3-2 Error Codes].
P2 card has been removed while being accessed (recorded, played back, or
formatted), and subsequent operation is disabled.
An error has occurred while recording data to or playing data from a P2 card.
In the actual indication the _ is replaced by the slot number of the P2 card
that triggered the error.
Something abnormal is happening to video and/or audio being recorded.
Backup battery needs replacing.
RF signal from the wireless receiver is degraded.
P2 card has no free space.
Playback position is at the start of all the clips.
Playback position is at the end of all the clips.
The P2 card is not recordable. Detailed information is provided on the
FUNCTION screen of MODE CHECK. See the relevant section of the
MODE CHECK indication area.
Clip cannot be played back perhaps because no P2 card is loaded, or the P2
card contains no clips.
Displayed when disconnection between microcomputers continues for a
specified period or longer.
Voice memos cannot be recorded, possibly perhaps because the P2 card has
no free space, or 100 voice memos are already recorded on one clip.
Voice memo being recorded.
Recording of voice memo stopped.
Voice memo being played back.
Shot mark been added or deleted. For information on shot marks, see [3-9
Shot Mark Function].
Clip information is being updated. Playback operation disabled.
AJ-SPC700P is in USB mode. When communication is disabled, the
indication blinks.
Thumbnail is being manipulated.
Displayed when the connection of the DVCPRO/DV connector is abnormal
(when AJ-YAD800G is attached).
Displayed when proxy recording on either the P2 card or the SD memory card
starts (when AJ-YAX800G is attached).
Displayed when proxy recording on the P2 card starts (when AJ-YAX800G is
attached.).
When the remaining free space on the SD Memory card drops below one
minute during proxy recording, the message is displayed (when AJ-YAX800G
is attached).
Displayed when full capacity is reached during proxy recording on the SD
memory card (when AJ-YAX800G is attached).
Displayed when proxy recording stops because of failure on either the video
encoder card or the stream.(when AJ-YAX800G is attached).
Displayed when a failure occurs on the SD memory card during proxy
recording, and only recording on the SD memory card stops.(when AJ-
YAX800G is attached).
Voice memo indication
Voice memo being recorded. When the free space for voice memos is less
than one minute, the indication blinks.
Audio input channel
and level meter
- - - - - - - - +
F
W
R
Selected channel together with its audio level.
AUDIO IN switch is positioned at FRONT.
AUDIO IN switch is positioned at WIRELESS.
AUDIO IN switch is positioned at REAR.
Time code indication
TCG 12:59:59:20
TCR 12:59:59:20
(V)UBG AB CD EF 00
(V)UBR 12 34 56 78
CTL –1:59:59:20
TCG (time code generator value)
TCR (time code reader value)
UBG VUBG
UBR VUBR.
Displays CTL count.
DV format indication
DV DV format specified and playback being performed in the DV format.
Iris override
indication
+ +
+
(No indication)
–
– –
Correction phase of the iris override (when active)
+ + : On the open side by 1 +: On the open side by 0.5
– – : On the closed side by 1 –: On the closed side by 0.5
No indication : Standard status
Iris, F value
NC
OPEN
F1.7 - F16
CLOSE
Lens cable is not connected.
Lens iris is at maximum.
Lens iris value
Lens iris closed.
<Note>
These indications are provided when the lens is capable of indicating the iris
value. When the iris is being overridden, they blink.
Zoom indication
Z00 - Z99 Zoom degree is indicated. This indication is not provided for a lens that does
not return the zoom position, even if the indication is set to ON.
V
#,52%2'PINKUJDQQMࡍࠫ㧞㧜㧜㧡ᐕ㧝㧞㧤ᣣޓᧁᦐᣣޓඦᓟ㧝㧞ᤨ㧠㧥ಽ