Filter
Top Products
Others
70
LSQT1091
3:A cassette cannot be inserted.
• Has condensation occurred? Wait until the
condensation indication disappears.
4:Auto focus function does not work.
• Is manual focus mode selected? If auto focus
mode is selected, focus is automatically
adjusted.
• There are some recording subjects and
surroundings for which the auto focus does not
operate correctly. (
-76-) If so, use the manual
focus mode to adjust the focus. (
-40-)
5:The Camcorder arbitrarily stops recording.
• Is the AGS function activated? Record in the
normal horizontal position or set [AGS] to
[OFF]. (
-36-)
Indications
1:A sentence is displayed in red in the screen
center.
• Read the contents and respond to them. (
-67-)
2:The time code becomes inaccurate.
0 The time code indication counter may not be
constant in the reversed slow-motion playback,
but this is not a malfunction.
3:The remaining tape time indication
disappears.
• The remaining tape time indication may
disappear temporarily during frame-by-frame
playback or other operation. If you continue
ordinary recording or playback, the indication is
restored.
4:The remaining tape time Indication does not
match the actual remaining tape time.
• If scenes of less than 15 seconds are
continuously recorded, the remaining tape time
cannot be correctly displayed.
• In some cases, the remaining tape time
indication may show remaining tape time that is
2 to 3 minutes shorter than the actual
remaining tape time.
5:A function indication such as mode
indication, remaining tape time indication or
time code indication is not shown.
• If you set [SETUP] >> [DISPLAY] >> [OFF],
indications other than the tape running
condition, warning and date indications
disappear.
Playback (Sound)
1:Sound is not played back from the built-in
speaker of the Camcorder.
0 Is the volume too low? During playback, push
the [s /VOLr] lever to display the volume
indication and adjust it. (
-42-)
2:Different sounds are reproduced at the
same time.
• Have you set [SETUP] >> [12bit AUDIO] >>
[MIX]? If you set [AUDIO REC] >> [12bit] and
dub audio to a recorded tape, you can hear the
sound on recording and the sound dubbed at a
later time. To hear the sounds separately, set
to [ST1] or [ST2]. (
-50-)
• Have you set [SETUP] >> [AUDIO OUT] >>
[STEREO] and reproduced a picture containing
the main sound and sub sound? Set to [L] to
hear main sound and set to [R] to hear the sub
sound. (
-65-)
3:Audio dubbing cannot be performed.
• Is the accidental erasure prevention slider on
the cassette open? If it is open (set to [SAVE]),
audio dubbing cannot be performed. (
-20-)
• Are you attempting to edit a tape portion that
was recorded in LP mode? LP mode does not
allow audio dubbing. (
-28-)
4:The original sound was erased when audio
dubbing was performed.
• If you perform audio dubbing on a recording
made in [16bit] mode, the original sound will be
erased. If you wish to preserve the original
sound, be sure to select [12bit] mode when
recording.
5:Sounds cannot be played back.
• Although a cassette with no audio dubbing is
being played, have you set [SETUP] >>
[12bit AUDIO] >> [ST2]? To play back a
cassette with no audio dubbing, set
[12bit AUDIO] >> [ST1].(
-50-)
• Is the variable speed search function working?
Press the [VAR SEARCH] button on the
remote control to cancel the variable speed
search function. (
-43-)
Playback (Pictures)
1: Although the Camcorder is correctly connected
to a TV, playback images cannot be seen.
The playback images are vertical.
• Have you selected video input on the TV?
Please read the operating instructions of your
TV and select the channel that matches the
input terminals used for the connection.
• Is the [TV ASPECT] setting correct? Change
the setting to match the aspect ratio of the TV.
[SETUP] >> [TV ASPECT] >> [16:9] or [4:3].
2:Mosaic-pattern noise appears on images
during cue or review playback.
• This phenomenon is characteristic of digital
video systems. It is not a malfunction.
3:Horizontal stripes appear on images during
cue and review playback.
• Horizontal stripes may appear depending on
the scene, but this is not a malfunction.
4:Playback picture is not clear.
• Are the heads of the Camcorder dirty? If the
heads are dirty, playback image cannot be
clear. Clean the heads by using the head
cleaner for digital video (optional). (
-72-)
• If the terminal for the Multi cable is soiled,
noises may appear on the screen. Wipe the soil
LSQT1091_ENG.book 70 ページ ２００６年１１月２７日 月曜日 午後１時１７分