Filter
Top Products
88
13. OTHERS
● Warning Indications for VCR Abnormalities
Should malfunctions occur during VCR operation, the unit self-diagnoses the cause and shows the diagnose together with an
error code on the LCD monitor or in the viewfinder.
Warning
WARNING7001
DRUM MOTOR FAILURE
Error code
Error Code Error Details GY-DV5000 Operation Remedy
0201
CONDENSATION ON DRUM
3200
LOADING FAILURE
3300
UNLOADING FAILURE
4100
CASSETTE EJECT FAILURE
TAPE DEFECTIVE
5605 ~ 5609
5702
TAPE END DET. ERROR
5802
TAPE BEGIN DET. ERROR
7001
DRUM MOTOR FAILURE
7101
CAP MOTOR FAILURE
7202 ~ 7203
SUPPLY REEL FAILURE
7302 ~ 7303
TAKE UP REEL FAILURE
7305
TAKE UP REEL FAILURE
7401
REEL MOTOR FAILURE
Indicates dew formation
(condensation)
Tape cannot be loaded.
Tape cannot be unloaded.
Irregularity with eject
operation.
Tape is cut.
Tape end sensor error.
Tape beginning sensor
error.
Drum rotation error.
Capstan rotation error.
Supply reel rotation error.
Ta ke up reel rotation error.
Irregular tape winding
when unloading.
Reel motor rotation error.
Leave the unit with the power ON,
until the indication disappears.
Switch the power OFF and then
switch it back ON. However, the
tape may be damaged depending
on the circumstances. Please
consult the person in charge of
professional video equipment at
your nearest JVC-authorized
service agent.
Press the EJECT button to take
out the cassette.
Switch the power OFF and then
switch it back ON. However, the
tape may be damaged depending
on the circumstances. Please
consult the person in charge of
professional video equipment at
your nearest JVC-authorized
service agent.
Operation stops. All operations
are rejected.
Operation stops.
Operation stops. All operations
are rejected.
■TALLY lamp
Blinks when remaining battery power or tape is low. (Only in Camera mode)
Blinking Pattern Remaining Battery/Tape
Slow blinking ● Remaining battery power is low.
(once per sec.) ● Remaining tape time is equivalent to less than 3 minutes.
Fast blinking ● Tape has run out.
(four times per sec.) ● Irregularity has occurred in the VCR.
13-1 Alarm Indications and Actions (Cont’d)
→
For servicing
Refer to the service manual page. 1-12 “1.9.11 ERROR HISTORY”
89
13. OTHERS
■Viewfinder Warning Lamps
REC
BATT
ALARM
1. 2.
Battery lamp REC/ALARM lamp
1.
BATTERY lamp
This red lamp lights red under the following circumstances.
Lights red : When the battery voltage becomes too low for
the camera to operate.
2.
REC/ALARM lamp
This lamp lights or blinks green under the following
conditions.
Lights Green : ● While recording
Blinks Green : ● During the interval where the unit
switches from record-standby to record
mode.
● Immediately before the tape runs out or
has run out.
● If the VCR malfunctions.
Whether or not alarm sound should be output and the
volume level are selected with the ALARM VR LEVEL item
on the OTHERS (2/2) menu screen.
■Alarm Sound
When remaining battery power becomes low, a warning
sound is output from the monitoring loudspeaker and the
PHONES jack. (In Camera mode only)
When an irregularity occurs in the VCR, a warning sound is
also output.
■Depending on the alarm conditions, the warning indicators on the LCD monitor/viewfinder screen, the TALLY lamp, the viewfinder
lamp, and alarm sounds appear as shown in the following table.
Alarm Indications
on LCD Monitor/
Viewfinder Screen
TALLY
Lamp
Lamp Viewfinder Lamp
Alarm Sound Condition
Alarm BATT
VTR alarm indication
(Example)
HEAD CLEANING
REQUIRED!
TAPE NEAR END
LOW VOLTAGE
and Voltage indication on
Status screen blinks
Display symbols :Blinking once per second. :Blinking four times per second.
:
Sound interrupted once per second.
:Continuous sound.
Dew formation (condensation) or error
has occurred in the VCR.
Video head clogging [Detected and
displayed during playback and edit search
in the Camera mode.]
About 3 min. before tape end
(displayed during recording).
Tape end
(displayed during recording).
Remaining battery power is low.
0701
DRUM MOTOR FAILURE