Filter
Top Products
33
3. BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS
1.
Tripod mounting holes
Front mount clip
2.
Safety lever
2.
Lock lever
3.
Rear base
mount
4.
Front
base
mount
Front mount clip
Pin
LIGHT
ON
OFF
COUNTER
CTL
TC
UB
RESET
OPERATE/WARNING
MONITOR
SELECT
STATUSSHUTTER
MENU
FILTER
1 3200k
2 5600k
3 5600k+ND
POWER
NG
GAIN
OUTPUT
WHT.BAL
VTR
ON OFF
ALARM
MONITOR
S
A
VE
S
T
B
Y
H
M
L
BA
R
S
C
AM
A
U
T
O
K
N
E
E
P
R
S
T
A
B
O
N
O
F
F
CH-1
CH-2
AUDIO
LEVEL
AUTO IRIS LOLUX
BACK L
NORMAL
SPOT L
STRETCH
NORMAL
COMPRESS
FULL AUTO BLACK
4.
3-6 Attaching the Tripod Base (provided)
Use the provided tripod base to place the camera on a tripod.
1.
Attach the tripod base on the tripod by using the hole that
balances the unit most optimally.
2.
While pushing the safety lever, pull the lock lever toward
the front until the front mount clip clicks into place.
3.
Place the unit on the tripod base by aligning the rear base
mount of the unit with the pin on the tripod base.
4.
Push the unit from the upward direction and slide it toward
the front so that the front base mount of the unit is locked
by the front mount clip of the tripod base as it clicks into
place.
• The front base mount may be locked while the pin of the
tripod base is not inserted into the hole on the rear base
mount of the unit. Therefore, after mounting, make sure
that these parts are engaged properly.
• When moving the unit mounted on a tripod, any impact
or vibration should be avoided as this may cause the unit
to become detached and to drop from the tripod.
Be sure to remove the unit from the tripod before
transporting it.
CAUTION:
For servicing
See the service manual page 1-16 “1.11.7 Tripod base”.
→
34
3. BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS
If the unit is not used for a lengthy period of time (one
month or more), remove the lithium battery. If the voltage
of the lithium battery becomes low, the set may malfunction.
"Li" indicator
Lithium battery case
Power switch
LIGHT
ON
OFF
COUNTER
CTL
TC
UB
RESET
OPERATE/WARNING
MONITOR
SELECT
STATUSSHUTTER
MENU
FILTER
1 3200k
2 5600k
3 5600k+ND
POWER
NG
GAIN
OUTPUT
WHT.BAL
VTR
ON OFF
ALARM
MONITOR
CH-1
CH-2
AUDIO
LEVEL
AUTO IRIS LOLUX
BACK L
NORMAL
SPOT L
STRETCH
NORMAL
COMPRESS
FULL AUTO BLACK
E
REV FWD
FBATT
H
HM
MSF
REMAIN
AUD LOCK
32k
CH 1
CH 2
48k
PB NDF
AUTO OFFDEW
L iRFSERVO
HOLD
SP
MENU
OVER
OVER
40 30 20 10 0
dB
H
M
L
SAVE STBY
BARS CAM
ON
OFF
A
U
T
O
K
N
E
E
P
R
S
T
A
B
TC GENERATOR
FREE
REC
PRESET
REGEN
CH-1
CH-2CH-1
CH-2
CH-1 CH-2
CONTINUE MENU
PRESETADVANCESHIFTHOLD
AUTO
MANUAL
FRONT
REAR
DATA SET
SELECTITEMGROUP
AUDIO SELECT
AUDIO INPUT
AUDIO
LEVEL
LITHIUM BATT.
CR2032
CR2032
LITHIUM BATT.
Lithium battery cover
CR2032
The GY-DV500 uses a lithium battery for backup of the time code data. Install the provided lithium battery before actually using the
unit.
● Lithium battery: CR2032
1.
Push the lithium battery cover in the direction of the arrow
as illustrated and remove the cover.
2.
Slide the battery into place with its marked surface facing
upward.
3.
Return the lithium battery cover to its original position in the
unit.
Ⅲ The lithium battery is easily removed
if you press at the edge of the
lithium battery at the place
indicated in the illustration on the
left and then pull the battery out.
Ⅲ How to Install the Lithium Battery Ⅲ How to Remove Lithium Batteries
3-7 Inserting and Replacing Backup Lithium Batteries
When the lithium battery is not in place or the battery is exhausted and requires a replacement, the "Li" indicator in the LCD display
will light up.
Replace lithium batteries with the POWER switch set to ON. Doing it with the POWER switch set to OFF will cause the loss of
backup data.
CAUTION:
After replacing the lithium battery, set the date and time.
To do this, see page 41 “Setting the Date and Time”.