Filter
Top Products
22
Parts and their Functions: Shooting and Recording/Playback Functions Section
19. MON OUT SEL (output signal selection) switch
Used to switch the signals output from the MON OUT
connector.
MEM: Video from the camera is output during
recording or when recording is paused or
playback signals are output from the P2 card
during playback.
CAM: Video from the camera is output constantly.
OFF: Video is not output, and the unit operates in
power-saving mode.
Note that the audio output is synchronized with the
video.
For types of video outputs, see [Settings of signals
output from HD SDI A · B connector] (page 89) or
[Settings of signals output from MON OUT connector]
(page 90).
Notes
During recording, this switch does not switch output
signals before stopping the recording operation.
Only a brightness signal is output in 1080/24PsF
when MONITOR OUT is set to “VBS”. MONITOR
OUT can be selected from the screen <OUTPUT
SEL> in the SYSTEM SETTING page.
20. REW (rewind) button and lamp
During stop, this button performs a fast-reverse
playback with the lamp lights on.
During playback, it performs an approximately 4 fast-
reverse playback with the PLAY and REW lamps lights
on.
If this button is pressed when playback is paused, the
start of the clip being played back is located in pause
mode.
21. STOP button
This button stops playback.
22. FF (fast forward) button and lamp
During stop, this button is used to perform fast playback
with the lamp lights on.
During playback, it performs an approximately 4 fast
playback with the PLAY and FF lamps lights on.
If this button is pressed when playback is paused, the
start of the next clip is located in pause mode.
23. PLAY/PAUSE button
This button is used to view playback using the
viewfinder screen or a color video monitor. The lamp
comes on when playback starts.
In playback mode, this button pauses (PLAY/PAUSE)
playback with the lamp blinking.
24. P2 card access LED
This LED indicates the recording and playback status of
each card.
25. Slide lock button
Used to open the slide-out door for inserting P2 cards.
While depressing this button, slide the door to the left.
26. USB 2.0 connector (DEVICE)
27. USB 2.0 connector (HOST)
A USB 2.0 cable is connected here.
When the menu option PC MODE is set to “ON”, data
can be transferred via USB 2.0. During such data
transfer, recording, playback or operations of clips is
limited.
The menu option PC MODE is found in the <SYSTEM
MODE> screen on the SYSTEM SETTING page. For
more information, see [Connection with external devices
using the USB 2.0 port] (page 147).
28. GENLOCK IN connector
Used to input an HD Y signal when GENLOCKing the
camera or externally locking the time code. Alternatively,
a composite signal can be input as the reference signal.
Note that the subcarriers for the down-converter
(composite signal) output from the unit cannot be
externally locked.
Note
When HD Y signal is input and the menu option RET
SW is set to “CAM RET”, you can check return video on
the viewfinder screen. The menu option RET SW can be
found in the <SW MODE> screen on the CAM
OPERATION page.
29. HD SDI B connector
This connector is for outputting video. A video signal
based on the setting of the 15. HD SDI A · B switch is
output. LinK B signal is output while in Dual Link output.
Note
Camera image is output from the HD SDI B connector
even during playback while in Dual Link (RGB 4:4:4)
output.
30. REMOTE (remote control) connector
The remote control unit AJ-RC10G (optional) is
connected here.
31. Option slot
Attach the video encoder card (AJ-YAX800G, optional).
For information about the installation and proxy
recording, see the AJ-YAX800G instruction manual.
AJ-HPX3700G-VQT1V68_eng.book 22 ページ ２００８年１０月１５日 水曜日 午後６時３８分