Filter
Top Products
M3099GX/GH OEM Manual IN-1
INDEX
Index
A
ABORT (Init → Targ)␣ ␣ 3-102
Abrasion counter␣ ␣ 4-6, B-2, B-6
ARBITRATION Phase␣ ␣ 3-16
Arbitration Delay␣ ␣ 3-12
Areas that must not be perforated␣ ␣ 6-4
Arrangement of units␣ ␣ 1-6
Assertion period␣ ␣ 3-12
Asynchronous Information Transfer␣ ␣ 3-20
Attention Condition␣ ␣ 3-24
Automatic document feeder (ADF)␣ ␣ 1-1, 1-6
B
BASIC OPERATION␣ ␣ 4-1
Basic Scanning Sequence (Simplex Mode):␣ ␣ 3-115
Belt Replacement␣ ␣ 4-19
Binarization and halftone function␣ ␣ 2-1
Buttons␣ ␣ 4-7
Bus Clear Delay␣ ␣ 3-12
BUS DEVICE RESET (Init → Targ)␣ ␣ 3-103
Bus Free Delay␣ ␣ 3-12
BUS FREE Phase␣ ␣ 3-15
Bus Set Delay␣ ␣ 3-12
Bus Settle Delay␣ ␣ 3-13
Buzzer B-2, B-4
C
Cable Skew Delay␣ ␣ 3-13
charge-coupled device (CCD) image sensors␣ ␣ 1-1
CLEANING␣ ␣ 8-1
Cleaning Locations and Frequencies␣ ␣ 8-1
Cleaning the glass surface␣ ␣ 8-7
Cleaning the rollers␣ ␣ 8-5
Cleaning the sensors␣ ␣ 8-7
Cleaning the transport paths␣ ␣ 8-6
Cleaning Tools␣ ␣ 8-2
Closing the Upper Transport Unit␣ ␣ 4-2
COMMAND COMPLETE (Init ← Targ)␣ ␣ 3-103
COMMAND Phase␣ ␣ 3-22
Command Sequence␣ ␣ 3-110
Commands␣ ␣ 3-27
Configuration␣ ␣ 1-5
Configuration of the scanner␣ ␣ 1-5
Consumables␣ ␣ 7-1
CONSUMABLES AND ACCESSORIES␣ ␣ 7-1
Control circuit (MPU)␣ ␣ 1-8
Control unit␣ ␣ 1-6
D
DATA IN Phase␣ ␣ 3-23
DATA OUT Phase␣ ␣ 3-23
Data Phase␣ ␣ 3-22
Data Release Delay␣ ␣ 3-13
Deskew Delay␣ ␣ 3-13
Device and Operator Actions for Equipment
Errors␣ ␣ 5-4
Device and Operator Actions for Temporary
Errors␣ ␣ 5-1
DISCONNECT (Init ← Targ)␣ ␣ 3-103
Disconnection Delay␣ ␣ 3-13
Document detection sensor␣ ␣ 8-8
Document Limitations␣ ␣ 6-4
Document Quality␣ ␣ 6-2
Document Size␣ ␣ 2-1, 6-1
DOCUMENT SPECIFICATION␣ ␣ 6-1
Document type␣ ␣ 6-2,␣ 6-8
Document width detection sensor␣ ␣ 8-7
Doouble-feed detection B-2, B-3
Drop-out Color␣ ␣ 6-7
#Z2 Index.pm5 98.2.22, 2:43 PM1