Filter
Top Products
35
4. POWER SUPPLY
■Flat shape type battery pack
■Anton-Bauer battery pack
●DIONIC 90
●Propack 13/14 Series
●Trimpack 13/14 Series
●Magnum 13/14 Series
●Compack 13/14 Series
AA-P250
DC cable
AC power adapter
PHONES
DC OUT
DC IN
DV
INT
REAR AUDIO IN
TALLY
CH-1
CH-2
The GY-DV5100 is operable with AC power supply or battery pack.
Use the JVC AA-P250 AC power adapter (max. rated output 12.5 V DC, 3.5 A) as the AC power supply.
1.
After making sure that the power switches of the GY-DV5100
and of the AA-P250 are set to OFF, connect the DC cable
from the AA-P250 to the DC IN connector of the GY-DV5100
as shown in the illustration.
2.
Set the CHARGE/CAMERA switch of the AA-P250 to
CAMERA.
3.
Press the POWER switch of the GY-DV5100 to ON. Power
is supplied to the VTR section and the camera.
* For details, read the instruction manual of the AA-P250.
The GY-DV5100 can be operated with the following battery packs.
● When the DC cable is connected to the DC IN connector, the power supply from the battery pack is interrupted and the power
starts to be supplied through the DC IN connector.
● Do not connect or disconnect the DC cable while operating with a battery pack.
The following symptoms may occur if the DC cable is connected or disconnected while operating with a battery pack.
• The power is cut off for a moment when the DC cable is disconnected.
• Noise to the video and audio signals occurs. Audio signal are muted.
● When operation is continued with DC input after the battery pack capacity has been used up, set the POWER switch to OFF
after the DC power is applied. Then switch ON again.
● If the GY-DV5100 is left with the battery pack attached, a small amount of power is consumed even if the POWER
switch on the GY-DV5100 is set to OFF. Remove the battery pack when the GY-DV5100 is not going to be used.
Do not use any power source with large fluctuations in the
power source voltage, power sources generating noise,
such as ripples or power sources with lower voltage.
4-1 AC Operation
4-2 Battery Pack Operation (Optional)
*A flat shape type battery pack cannot be connected directly
to the camera. It is necessary to mount the optional battery
case.
Battery case: SCV2978-002
See “Attaching the NP-1B type Battery” on page 36.
MEMO:
Do not remove or connect the DC cable while recording is
being performed.
4. POWER SUPPLY
E-35
■Flat shape type battery pack
■Anton-Bauer battery pack
●DIONIC 90
●Propack 13/14 Series
●Tr impack 13/14 Series
●Magnum 13/14 Series
●Compack 13/14 Series
AA-P250
DC cable
AC power adaptor
PHONES
DC OUT
DC IN
DV
INT
REAR AUDIO IN
TALLY
CH-1
CH-2
The GY-DV5100 is operable with AC power supply or battery pack.
Use the JVC AA-P250 AC power adapter (max. rated output 12.5 V DC, 3.5 A) as the AC power supply.
The GY-DV5100 can be operated with the following battery packs.
● When the DC cable is connected to the DC IN connector, the power supply from the battery pack is interrupted and the power
starts to be supplied through the DC IN connector.
● Do not connect or disconnect the DC cable while operating with a battery pack.
The following symptoms may occur if the DC cable is connected or disconnected while operating with a battery pack.
• The power is cut off for a moment when the DC cable is disconnected.
• Noise to the video and audio signals occurs. Audio signal are muted.
● When operation is continued with DC input after the battery pack capacity has been used up, set the POWER switch to OFF
after the DC power is applied. Then switch ON again.
● If the GY-DV5100 is left with the battery pack attached, a small amount of power is consumed even if the POWER
switch on the GY-DV5100 is set to OFF. Remove the battery pack when the GY-DV5100 is not going to be used.
Do not use any power source with large fluctuations in the
power source voltage, power sources generating noise,
such as ripples or power sources with lower voltage.
4-1 AC Operation
4-2 Battery Pack Operation (Optional)
* An Anton-Bauer battery pack cannot be connected directly
to the GY-DV5100. It is necessary to mount the optional
battery holder.
Battery holder: Anton-Bauer QR JVC DIGI
For details on how to mount the battery holder, see page
37.
Do not remove or connect the DC cable while recording is
being performed.
1.
After making sure that the power switches of the GY-DV5100
and of the AA-P250 are set to OFF, connect the DC cable
from the AA-P250 to the DC IN connector of the GY-DV5100
as shown in the illustration.
2.
Set the CHARGE/CAMERA switch of the AA-P250 to
CAMERA.
3.
Press the POWER switch of the GY-DV5100 to ON. Power
is supplied to the VTR section and the camera.
*For details, read the instruction manual of the AA-P250.
MEMO:
E
U