Filter
Top Products
67
10. TIME CODE OPERATION
10-1 Displaying Time Code
The GY-DV5100 records SMPTE-standard time codes and user’s bits. In the play mode or the record mode, the reproduced time
codes or user’s bits are shown on the LCD monitor or in the viewfinder.
● Time code data cannot be output through the unit’s connectors.
OPEN
CH-1
AUDIO IN
AUDIO SELECT
CH-2
CH-1 CH-2
FRONT
REAR
AUTO
MANUAL
AUDIO
LEVEL
CH-1 CH-2
PULL
OPEN
LCDBRIGHT DISPLAY
COUNTER
CH-1
AUDIO IN
AUDIO SELECT
CH-2
CH-1 CH-2
FRONT
REAR
AUTO
MANUAL
TC GENE.
TC
MONITOR
SELECT
AUDIO
LEVEL
REAR
AUDIO IN
CH-1 CH-2
CH-1
MIX
CH-2
CH-1 CH-2
LINE
MIC
+48V
PRST
REGEN FREE
REC
UB
LCDBRIGHT DISPLAY
FRONT MIC +48V
OFF
ON
00:00:00:00
STBY 01/02/03 01:23:45
The time codes or user’s bits can be shown on the LCD monitor
or in the viewfinder during playback and recording as follows.
(Status screen)
Setting
1.
Set the TC/UB item on the LCD/VF (2/2) menu screen to
ON.
● Time codes or user’s bit data are displayed on the Status
screen.
2.
Whether time codes or user’s bit data should be displayed
is selected with the COUNTER switch inside the cover on
the side.
TC :Time codes are displayed.
The symbol between the seconds and the frame
differs with the framing mode. (Colon or dot)
UB : User’s bit data is displayed.
Time code entered from the DV connector
COUNTER switch
Time code indication
Status 1 screen
Example
Time code indication
00:00:00:00
Non-drop frame (:)
Drop frame (.)
User’s bits indication
FF EE DD 20
MEMO:
● The time code and user’s bit input from the DV terminal
are not recorded. The data generated by the camera’s
time code generator is recorded.
● To maintain the continuity of time code data, use with
the TC GENE. switch set to REGEN mode when
recording input signal from the DV terminal.
■Time code entered from the DV connector
Pressing the STOP button for 1 second in the EJECT or stop
mode displays the time code data or user’s bit data input
from the DV terminal on the Status screen.
DTCG : The time code data from the DV terminal
DUBG : The user’s bit data from the DV terminal
To return to display of the original time code or user’s bit,
press the STOP button.
(Display of the normal time code or user’s bit is also restored
by performing VTR operation.)
10. TIME CODE OPERATION
E-67
10-1 Displaying Time Code
The GY-DV5100 records EBU-standard time codes and user’s bits. In the play mode or the record mode, the reproduced time
codes or user’s bits are shown on the LCD monitor or in the viewfinder.
● Time code data cannot be output through the unit’s connectors.
OPEN
CH-1
AUDIO IN
AUDIO SELECT
CH-2
CH-1 CH-2
FRONT
REAR
AUTO
MANUAL
AUDIO
LEVEL
CH-1 CH-2
PULL
OPEN
LCDBRIGHT DISPLAY
COUNTER
CH-1
AUDIO IN
AUDIO SELECT
CH-2
CH-1 CH-2
FRONT
REAR
AUTO
MANUAL
TC GENE.
TC
MONITOR
SELECT
AUDIO
LEVEL
REAR
AUDIO I N
CH-1 CH-2
CH-1
MIX
CH-2
CH-1 CH-2
LINE
MIC
+48V
PRST
REGEN FREE
REC
UB
LCDBRIGHT DISPLAY
FRONT MIC +48V
OFF
ON
00:00:00:00
STBY 01/02/03 01:23:45
The time codes or user’s bits can be shown on the LCD monitor
or in the viewfinder during playback and recording as follows.
(Status screen)
Setting
1.
Set the TC/UB item on the LCD/VF (2/2) menu screen to
ON.
● Time codes or user’s bit data are displayed on the Status
screen.
2.
Whether time codes or user’s bit data should be displayed
is selected with the COUNTER switch inside the cover on
the side.
TC : Time codes are displayed.
UB : User’s bit data is displayed.
■Time code entered from the DV connector
Pressing the STOP button for 1 second in the EJECT or stop
mode displays the time code data or user’s bit data input
from the DV terminal on the Status screen.
DTCG : The time code data from the DV terminal
DUBG : The user’s bit data from the DV terminal
To return to display of the original time code or user’s bit,
press the STOP button.
(Display of the normal time code or user’s bit is also restored
by performing VTR operation.)
MEMO:
● The time code and user’s bit input from the DV terminal
are not recorded. The data generated by the camera’s
time code generator is recorded.
● To maintain the continuity of time code data, use with
the TC GENE. switch set to REGEN mode when
recording input signal from the DV terminal.
This does not apply to GY-DV5100E.
COUNTER switch
Time code indication
Status 1 screen
Example
Time code indication
00:00:00:00
User’s bits indication
FF EE DD 20
E
U