Filter
Top Products
68
10. TIME CODE OPERATION
OPEN
CH-1
AUDIO IN
AUDIO SELECT
CH-2
CH-1 CH-2
FRONT
REAR
AUTO
MANUAL
AUDIO
LEVEL
CH-1 CH-2
PULL
OPEN
LCDBRIGHT DISPLAY
COUNTER
CH-1
AUDIO IN
AUDIO SELECT
CH-2
CH-1 CH-2
FRONT
REAR
AUTO
MANUAL
TC GENE.
TC
MONITOR
SELECT
AUDIO
LEVEL
REAR
AUDIO IN
CH-1 CH-2
CH-1
MIX
CH-2
CH-1 CH-2
LINE
MIC
+48V
PRST
REGEN FREE
REC
UB
LCDBRIGHT DISPLAY
FRONT MIC +48V
OFF
ON
––– TC/UB/CLOCK –––
TC PRESET 00:00:00:00
EXECUTE
UB PRESET 00 00 00 00
EXECUTE
DROP/NON DROP DROP
TIME/DATE..
PAGE BACK
HEADER REC..
10-2 Presetting and Recording of Time Code
To preset the Time Code, make the following settings.
■TC GENE. switch
Set to PRST REC or PRST FREE.
PRST REC : The data preset in the time code generator
runs only during recording.
Use this setting if it is necessary to record
continual time codes across different scenes.
* However, approximately ±1-frame variations
may occur in scene accuracy.
PRST FREE : The time code starts to run from the time it is
preset in the time code generator.
■TC/UB/CLOCK menu screen
Use the DROP/NON DROP item to select the framing mode
for the time code generator.
DROP : The time code generator’s running method is
set to the drop frame mode.
Use this setting when placing emphasis on
the recording time.
NON DROP : The time code generator’s running method is
set to the non drop frame mode.
Use this setting when placing emphasis on
the number of frames.
Framing mode:
Non-drop/Drop setting
TC GENE. switch
TC/UB/CLOCK menu screen
Drop frame/Non-drop frame mode
In the NTSC system, the actual number of frames per 1 second is approximately 29.97 frames, but per time code 30 frames are
processed. To compensate for this difference, the mode called “drop mode” drops frame 00 and 01 for every minute not divisible
by 10.
The “non-drop frame mode” is when no frames are dropped and the actual time shift is neglected.
The time codes or user’s bit data from the internal time code generator can be recorded at the time of recording scenes.
10. TIME CODE OPERATION
E-68
FRONT MIC +48V
OFF
ON
OPEN
CH-1
AUDIO IN
AUDIO SELECT
CH-2
CH-1 CH-2
FRONT
REAR
AUTO
MANUAL
AUDIO
LEVEL
CH-1 CH-2
PULL
OPEN
LCDBRIGHT DISPLAY
COUNTER
CH-1
AUDIO IN
AUDIO SELECT
CH-2
CH-1 CH-2
FRONT
REAR
AUTO
MANUAL
TC GENE.
TC
MONITOR
SELECT
AUDIO
LEVEL
REAR
AUDIO I N
CH-1 CH-2
CH-1
MIX
CH-2
CH-1 CH-2
LINE
MIC
+48V
PRST
REGEN FREE
REC
UB
LCDBRIGHT DISPLAY
––– TC/UB/CLOCK –––
TC PRESET 00:00:00:00
EXECUTE
UB PRESET 00 00 00 00
EXECUTE
UB REC ON
TIME/DATE..
PAGE BACK
HEADER REC..
10-2 Presetting and Recording of Time Code
To preset the Time Code, make the following settings.
■TC GENE. switch
Set to PRST REC or PRST FREE.
PRST REC : The data preset in the time code generator
runs only during recording.
Use this setting if it is necessary to record
continual time codes across different
scenes.
*However, approximately ±1-frame
variations may occur in scene accuracy.
PRST FREE : The time code starts to run from the time it
is preset in the time code generator.
TC GENE. switch
TC/UB/CLOCK menu screen
The time codes from the internal time code generator can be recorded at the time of recording scenes.
Whether or not user’s bit data should be recorded can be selected with the UB REC item on the TC/UB/CLOCK menu screen.
E
U