Filter
Top Products
62
Functions which can be selected
INH:
No functions are allocated.
S.GAIN:
The S.GAIN function is allocated.
DS.GAIN:
The DS.GAIN function is allocated.
LINE MIX:
The LINE MIX GAIN (+6 dB) function is allocated.
S.IRIS:
The SUPER IRIS function is allocated. This is useful
when providing backlight compensation.
I.OVR:
The IRIS override function is allocated.
This changes the target (reference) value in the auto iris
mode.
To change the target value, first establish this mode, and
then press the JOG dial button to enable the target value
to be changed. The target value is changed by turning
the JOG dial button clockwise or counterclockwise. “+,”
“+ +,” “–” or “– –” is displayed on the left of the iris display
area on the viewfinder screen. Stop turning the JOG dial
button at the position to be changed, and press the JOG
dial button to enter the change in the target value.
To release this mode, press the USER button again. Once
the power is turned off, the value returns to the default
value.
+: The aperture is opened by a half stop.
+ +: The aperture is opened by a full stop.
–: The aperture is stopped down by a half stop.
– –: The aperture is stopped down by a full stop.
No display:
The reference value remains unchanged.
S.BLK:
The SUPER BLACK function is allocated. This function
reduces the black level to below the pedestal level.
4-9-3 Allocating functions to the USER
MAIN, USER1 and USER2 buttons
The desired functions can be allocated to the USER MAIN,
USER1 and USER2 buttons.
To select this function, perform menu operations to open the
<USER SW> screen from the OPERATION page, and set
the desired function each with the USER MAIN SW item,
USER1 SW item and USER2 SW item.
<Note>
Once the power of the unit is turned OFF, functions assigned
to the USER button are disabled. When the power is turned
ON again, press the USER button to enable the assigned
functions.
< USER SW >
#
USER MAIN SW :S.GAIN
USER1 SW :PRE REC
USER2 SW :DS.GAIN
Chapter 4 Adjustments and settings for recording
(continued)
B.GAMMA:
The BLACK gamma function is allocated. This function
highlights the black gradations.
Regardless of the value set in the BLACK GAMMA item
on the menu (<LOW SETTING> screen, <MID SETTING>
screen and <HIGH SETTING> screen on the PAINT
page), the BLACK GAMMA is set to “+2”.
AUDIO CH1:
The function for switching the channel 1 input signal is
allocated. Each press advances the setting through the
sequence FRONT > W.L.> REAR. Note that it is also
possible to change the setting by operating the AUDIO IN
switch. Whichever control is operated last takes
precedence.
AUDIO CH2:
The function for switching the channel 2 input signal is
allocated. Each press advances the setting through the
sequence FRONT > W.L.> REAR. Note that it is also
possible to change the setting by operating the AUDIO IN
switch. Whichever control is operated last takes
precedence.
REC SW:
The function of the VTR’s START button is allocated.
Y GET:
The function for displaying the brightness level of the
center marker area is allocated.
RET SW:
The function of the RET button on the lens is allocated.
PRE REC:
The function to turn ON/OFF the PRE RECORDING is
allocated.
Time for executing the PRE RECORDING is set by using
the PRE REC TIME item after performing menu
operations to open the <REC FUNCTION> screen from
the SYSTEM SETTING page.
DRS:
The function of the dynamic range stretcher is allocated.
The function is allocated to compress the video level with
high brightness and stretched the dynamic range.
<Notes>
O Since the DRS function compresses the video levels of
sections with high brightness, there are slight
differences in color development when the DRS
function is turned on/off.
O When the DRS function is turned on, the Knee function
and the BLACK GAMMA function are not available.
O To operate the DRS function, turn the LINE MIX GAIN
function OFF.