JVC GY-DV550U Camcorder User Manual


 
6. SETTING AND ADJUSTMENTS BEFORE SHOOTING
50
INTERCOM
DC INPUT
DV
AUDIO IN
EARPHONE
DC
OUTPUT
LINE MIC
+48V
ON ON
LINE MIC
+48V
REAR
FRONT
VF
AUTO
WHITE
SKIN
AREA
ACCU
FOCUS
TAKE
VTR
PUSH
ZEBRA
AUDIO
LEVEL CH-1
ON
OFF
SHUTTERSTATUS
MENU
FILTER
3200k
1
5600k+1/8ND
2
5600k+1/64ND
3
ALARM
MONITOR
OPERATE
NG
G
A
IN
OU
TP
UT
W
HT.BA
L
V
TR
ON OFF
AUTO IRIS
LOLUX
BACK L
NORMAL
SPOT L
STRETCH
NORMAL
COMPRESS
LIGHT
ON
OFF
COUNTER
AUDIO SELECT
MANUAL
AUTO
CH-1 CH-2 CH-1 CH-2
REAR
FRONT
RM
AUDIO INPUT
MODE
CTL
TC
UB
CH-1
MIX
CH-2
RESET
OPERATE/WARNING
MONITOR
SELECT
CH-1
AUDIO
LEVEL
CH-2
VTR
ON
OFF
INCOM
MIC
INCOM
MIC
LEVEL
POWER
OFFRM
DC IN
/BATT.
CALL
CARBON
DYNAMIC
FULL AUTO BLACK
AUDIO SELECT
MANUAL
AUTO
CH-1 CH-2 CH-1 CH-2
REAR
FRONT
AUDIO INPUT
CH-1
AUDIO
LEVEL
CH-2
6-9 Audio Input Signal Selection
The GY-DV550 is provided with the AUDIO INPUT connector
on the front section and the AUDIO INPUT connectors at the
rear section for audio input.
Two channels of sound can be recorded on the tape in digital
PCM format.
Using the AUDIO INPUT switch, select for each channel (CH1
and CH2) whether the sound to be recorded should be the
sound from the AUDIO INPUT connector on the front section
or the sound from the AUDIO INPUT connectors on the rear
section.
Selecting the CH-1 channel input sound
Make the selection using the CH-1 AUDIO INPUT switch.
FRONT : The sound from the AUDIO INPUT connector on
the front section is recorded on the CH-1 channel.
REAR : The sound from the AUDIO INPUT connector on
the rear section is recorded on the CH-1 channel.
Selecting the CH-2 channel input sound
Make the selection using the CH-2 AUDIO INPUT switch.
FRONT : The sound from the AUDIO INPUT connector on
the front section is recorded on the CH-2 channel.
REAR : The sound from the AUDIO INPUT connector on
the rear section is recorded on the CH-2 channel.
Selection of front audio input and rear audio input
connectors
Select the audio signal input to the AUDIO IN FRONT and
AUDIO IN REAR connector using the [LINE/MIC] switch.
Make settings for the AUDIO IN FRONT and AUDIO IN
REAR connectors separately.
LINE : Set to this position when connected to audio
equipment, etc.
The reference input level is +4 dBs.
MIC : Set to this position when using a monaural
microphone.
The reference input level is -60 dBs.
MIC +48 V : Set to this position when a microphone
(phantom microphone) requiring +48 V DC
power supply is connected.
AUDIO IN FRONT
connector
AUDIO IN
REAR
LINE/MIC
switch
AUDIO IN
FRONT
LINE/MIC
switch
AUDIO
IN REAR
connector
CH-1 AUDIO
INPUT switch
CH-2 AUDIO
INPUT switch
When connecting a component that does not require
+48 V power supply, make sure that the LINE/MIC switch
is not set to MIC +48V.
Neglecting this could cause damage to the connected
component.
CAUTION: