JVC GY-DV550U Camcorder User Manual


 
10. S.S.F. (Super Scene Finder) FUNCTION
69
10-5 Writing S.S.F. Data to Tape
10-6 Outputting S.S.F. Data
SHUTTERSTATUS
MENU
FILTER
3200k
1
5600k+1/8ND
2
5600k+1/64ND
3
ALARM
MONITOR
OPERATE
NG
GAIN
OUTPUT
WHT.BAL
VTR
ON OFF
AUTO IRIS
LOLUX
BACK L
NORMAL
SPOT L
STRETCH
NORMAL
COMPRESS
LIGHT
ON
OFF
COUNTER
AUDIO SELECT
MANUAL
AUTO
CH-1 CH-2 CH-1 CH-2
REAR
FRONT
RM
AUDIO INPUT
MODE
CTL
TC
UB
CH-1
MIX
CH-2
RESET
OPERATE/WARNING
MONITOR
SELECT
CH-1
AUDIO
LEVEL
CH-2
VTR
ON
OFF
INCOM
MIC
INCOM
MIC
LEVEL
POWER
OFFRM
DC IN
/BATT.
CALL
CARBON
DYNAMIC
FULL AUTO BLACK
LOG REW FF
PLAY STILL
STOP
AUDIO SELECT
CONTINUE
MANUAL
AUTO
INT
EXT
AUX
GROUP ITEM SELECT DATA SET
HOLD SHIFT ADVANCE PRESET
CAM
CH-1 CH-2 CH-1 CH-2
REAR
FRONT
AUDIO INPUT
CH-1
SEE
INSTR-
UCTION
MANUAL
CH-2
AUDIO
LEVEL
VTR SELECT
VTR INPUT
PARA
REC
FREE
PRST
REGEN
TC GENE.
MENU
LITHIUM BATT.
CONTINUE button
2.
LOG button
2.
REW button
1.
STOP button
1.
Press the STOP button to enter the stop mode.
2.
Press the REW button while the LOG button is kept pressed.
The REW indicator blinks during tape transport in the
writing position.
The LOG indicator lights while S.S.F. data are being
written to the tape.
When writing to the tape is completed, the LOG indicator
goes out.
Operation
S.S.F. data stored in the unitís memory can be written to the
beginning of tape.
About the Scene End Cue Up Function
When the CONTINUE button is pressed while the LOG
button is kept pressed in the stop mode, the tape winds
to the S.S.F. datas last OUT point, after which the unit
enters the record-pause mode. (Scene End Cue Up)
The FF buttons LED blinks during the Scene End Cue
Up mode.
Precautions when writing S.S.F. data
When S.S.F. data stored in the memory of the GY-DV550
is written to the beginning of the rewound tape,
approximately 5 seconds of recorded video and/or sound
will be erased at the beginning.
In the case of important recordings, leave 5 seconds or
more of the tape unrecorded before starting recording.
Writing of S.S.F. data should be done with the DC cable
disconnected.
Once a tape with recorded S.S.F. data is ejected and then
reinserted again, the previous data will be erased if new
S.S.F. data are recorded on the tape.
Note:
The S.S.F. data in the memory of the main unit or that recorded
at the beginning of the tape can be output via the REMOTE
connector using the RS-232C controller.
For how to make connections for this, refer to Connecting a
PC on page 71.
In the stopped condition, the GY-DV550 answers with the S.S.F.
data when it receives the RS-232C command D5h S.S.F. DATA
SENSE from the PC.
(Indication example)
START
ID NO: 2c97
REEL NO: 1818
SCENE MARK IN MARK OUT CUE
001M 00:00:00:16 00:00:04:19
002M 00:00:06:03 00:00:08:08
003C 00:03:15:17 00:03:57:00
004C 00:03:58:18 00:05:37:24 00:04:00:21
004C 00:03:58:18 00:05:37:24 00:04:07:22
004C 00:03:58:18 00:05:37:24 00:04:18:23
END
When recording in the S.S.F. mode is completed, and the
cassette tape has not been taken out, the S.S.F. data stored
in the memory of the GY-DV550 are output when the RS-
232C command D5h is received.
If the tape recorded in S.S.F. mode is ejected and then loaded
again, the GY-DV550 rewinds the tape to the beginning and
plays back for about 10 seconds when it receives the RS-
232C command D5h.
During the playback, the model lD data and reel number
recorded on the tape are read. If corresponding S.S.F. data
are found in the memory, these data are output.
If corresponding S.S.F. data are not found in the memory, the
tape is rewound to the beginning once more, and after about
20 seconds of slow playback the stop mode is entered.
During slow playback, if S.S.F. data are written at the
beginning of the tape, these data are read out, and after the
stop mode is entered the S.S.F. data are output.
If S.S.F. data does not exist, the 05h (NOT TARGET)
command is output.
Operation
Operation