Filter
Top Products
18
D14049.03
MAY 2008
Grey Headline (continued)
To set the initial conguration using a PC
connected to the VCS DATA port via a serial
cable:
Connect the supplied serial cable from the 1.
DATA port on the VCS to the COM port on a
PC.
Start a terminal emulator program on the 2.
PC and congure it to use the DATA port as
follows:
baud rate 115200
•
data bits: 8
•
parity: none
•
stop bits: 1
•
ow control: none.
•
Power on the unit (if it is not already on).3.
The terminal emulator program will display
start up information.
After approximately 2 minutes you will get
the login prompt (if the unit is already on,
press Enter to get the login prompt):
tandberg login:
Enter the username 4. admin and press Enter.
You will get the password prompt:
Password:
Enter the default password of 5. TANDBERG
and press Enter.
You will get the install wizard prompt:
Run install wizard [n]:
Type y and press Enter.
Follow the prompts given by the install 6.
wizard to specify the following:
The password you want to use for your a.
system. See Administrator Account
Password for details.
Whether you wish to use IPv4 or IPv6. b.
See IP Protocol for details.
The LAN 1 IP address of the system. c.
The LAN1 IPv4 subnet mask of the system d.
(if you have selected IPv4).
The IP default gateway of the system. e.
The f. ethernet speed.
Whether you want to use SSH to g.
administer the system.
Whether you want to use Telnet to h.
administer the system.
Once the wizard is nished you will be 7.
prompted to log in again. Login with the
username admin and your new password.
You will again get the install wizard prompt; 8.
this time select n and press Enter in order
to skip the wizard.
A welcome message similar to the following
will appear:
Welcome to
TANDBERG Video Communication
Server Release X2.0
SW Release Date: 2008-03-20
OK
You must now reboot the system in order 9.
for the new settings take effect. To do this,
type the command:
xCommand boot
•
Once it has rebooted, the VCS is ready to use.
You can continue to use the serial connection,
or you can connect to the system remotely over
IP using either or both:
the
•
web interface via HTTPS
a
•
command line interface via SSH or Telnet.
We recommend that you now congure the
following:
The system name of the VCS. This is used by
•
the TANDBERG Management Suite (TMS) to
identify the system. See About the System
Name for more information.
Automatic discovery. If you have multiple
•
VCSs in the same network you may want
to disable automatic discovery on some
of them. See Auto Discover for more
information.
The DNS server address (if URI dialing
•
or FQDNs are to be used). See DNS
conguration for more information.
To start the VCS:
Ensure the power cable is connected. 1.
Ensure the LAN cable is connected to the 2.
LAN1 port.
Turn on the power switch on the back right 3.
of the unit (adjacent to the power cable).
Press the soft power button on the back left 4.
of the unit.
The system will power up. Wait until:
the green PWR LED on the front of the unit
•
is a steady green color (it may ash briey
during power up).
the red ALM LED on the front of the unit has
•
gone out.
the IP address is showing in the display
•
panel on the front of the unit.
You now must set the system's IP address,
subnet mask and default gateway before the
system can be used. Consult your network
administrator for information on which
addresses to use. Note that the VCS must use
a static IP address.
The initial conguration can be done:
by connecting from a PC to the VCS
•
via a
serial cable
via the buttons on the front pane
•
l
if your network is set up to allow it, by
•
connecting via a web browser to the default
IP address of 192.168.0.100.
Powering on the VCS Initial Conguration via Serial Cable
!
Do not leave a terminal emulator
session open once it is no longer in
use. An open session may cause
issues during a system restart.
The IP conguration made via the serial
cable applies to the LAN 1 ethernet
port only. If you have enabled the
LAN 2 port (by installing the Dual Network
Interfaces option key) you must use the web
interface or CLI to congure the LAN 2
settings.
!
If the red ALM LED ashes rapidly it
indicates a hardware fault. Contact your
local TANDBERG representative.
The yellow HDD LED indicates disk activity and
may icker during normal operation, more so
on a busy system.
TANDBERG VIDEO COMMUNICATIONS SERVER
ADMINISTRATOR GUIDE
Introduction Getting Started
Overview and
Status
System
Conguration
VCS
Conguration
Zones and
Neighbors
Call
Processing
Bandwidth
Control
Firewall
Traversal
Maintenance Appendices
Initial Conguration