Filter
Top Products
46
Setting the Camera Outputs
Chapter 3 Basic Adjustments and Settings
MLUT SEL
Select a monitor LUT to be applied.
In the default condition, you can select from among the
following signals, which correspond to S-LOG gamma:
When USER is selected at the TABLE line on the
<GAMMA> page of the USER (PAINT) menu, a user-
defined MLUT loaded from a “Memory Stick” can be
selected.
For details on the user-defined MLUT, see “User-MLUT
file” (page 100).
[MLUT]
Select MLUT at the MLUT/PBMIX line and activate/
deactivate the monitor LUT independently for each VF,
MONI, and VBS signal in the respective [MLUT]
columns.
When OFF or PBMIX is selected at the MLUT/PBMIX
line, (OFF) is displayed and cannot be changed.
• As MLUT images are converted from the images of the
main line, picture adjustments in Custom mode will be
reflected on the main line and MLUT images at the same
time. Do not perform any picture adjustment while
observing an MLUT output image.
• MLUT is automatically set to OFF when you change the
gamma table or gamma category for the main line on the
<GAMMA> page of the USER (PAINT) menu.
• MLUT cannot be selected if the gamma table is set to
STANDARD or HYPER GAMMA (see page 58).
To display the MLUT mark
MLUT MARK
When monitor LUT is applied to the SDI output at the
MONITOR OUT connectors and the viewfinder images,
you can set the camera to display the MLUT mark [LUT] to
indicate that gamma that is different from that used for
recording is applied. (The mark is not recorded with the
docked recorder.)
Set MLUT MARK to ON then set the brightness and
position of the indication.
To monitor the playback picture
The playback picture of the recorder can be confirmed with
a monitor connected to the camera or on the viewfinder
screen.
[CAM/PB]
If MLUT/PBMIX is MLUT or OFF, the playback-signal
output mode can be selected for each VF, MONI, or VBS
signal.
If the recorder is turned off with PB selected, the picture on
the viewfinder/monitor screen is distorted. The normal
picture is restored when you turn the recorder on or set it
to AUTO or CAM.
To compare the playback picture and
camera image
When PBMIX is selected on the MLUT/PBMIX line, the
playback picture and camera image can be displayed on
the same screen with all the outputs.
How this is to be displayed can be set on the <PB MIX
SETTING> page of the USER (OPERATION) menu.
Setting Signal
709 (800%) Signal expanding the dynamic range to 800%
based on ITU-R709
HG8009G40 Signal same as Hyper Gamma No. 7,
HG8009G40
HG8009G33 Signal same as Hyper Gamma No. 8,
HG8009G33
709 (180%) Signal same as the conventional monitor
gamma (knee point: 87%, dynamic range:
180%)
Setting Function
ON For applying the MLUT appropriate for
checking images.
During playback, it changes to (ON) and
cannot be changed.
OFF For displaying the same video signal as that
of the main line
Notes
Item Function
LEVEL For selecting the brightness of the gamma
mark in the range of 1–4 (4 for the
maximum brightness)
H POS For setting the horizontal position of the
indication in the range of 0–99 (0 for the
leftmost)
V POS For setting the vertical position of the
indication in the range of 0–99 (0 for the
uppermost)
Setting Content
PB The playback picture of the recorder is always
output.
AUTO
(Default)
Normally, the camera image is output. When
the recorder enters a playback mode (PLAY,
FF, REW, or REC REVIEW), the playback
picture is automatically selected.
CAM The camera image is always output.
Note