Filter
Top Products
49
Viewing and Setting the Viewfinder Displays
Chapter 3 Basic Adjustments and Settings
The set NEAR END and END values can be checked on
the <BATTERY ALARM> page of the USER
(OPERATION) menu.
c Focus position
Shows the focus position of a zoom lens as a numeric
value.
With an ARRI LDS lens: 0 to 1023
With a Cooke /i lens: 0.00m to 999m
May be shown in inches with some lenses:
0000000 to 9999999 (inches
×10)
With a lens control unit connected: Not displayed
d Zoom position
Indicates the approximate position of the zoom lens
variator between wide angle and telephoto.
With an ARRI LDS lens: Z0 (wide) to Z1023 (tele)
With a Cooke /i lens: Z1 (wide) to Z9999 (tele)
(focal length: 1mm to 9999mm)
With a lens control unit connected: Z0 (wide) to Z99
(tele)
1)
1) The items to be displayed may vary depending on the connected lens
control unit.
e White balance memory
Displays the currently selected white balance memory.
W:A: Memory A
W:B: Memory B
W:P: Preset memory
The setting is fixed at W:P in Cine mode.
In Custom mode, you can change the setting using the
subdisplay or from a remote control unit.
f Color temperature filter mode
Indicates the condition of the electrical filter.
In Cine mode, “5600” is displayed when the daylight filter
is selected. When the tungsten filter is selected, this
column becomes blank.
In Custom mode, “5600” is displayed when 5600K is set
to ON.
g Optical filters
Displays the types of filters currently selected.
h Gain value
Displays the video gain value (dB) of the video amplifier.
i Shutter
The shutter setting is displayed with the shutter angle or
frequency. For a shutter angle, is displayed at the left.
The type of the display, angle (deg) or speed (sec), can also
be switched on the <VF DISPLAY> page of the USER
(OPERATION) menu (default: deg).
j Tape remaining
The remaining time of the tape of the recorder docked on
the camera is roughly indicated in minutes.
k Recording mode
“REC” is displayed when the recorder docked on the
camera is in REC mode.
l Iris setting
Indicates the iris setting of the lens.
With an ARRI LDS lens: I0 to I1023
With a Cooke /i lens: T0 to T99999
With a lens control unit connected: F1.7 to F22, or CL
1)
1) The items to be displayed may vary depending on the connected lens
control unit.
m Self-diagnosis information
“CAM?” is displayed if an error is generated, e.g., on an
internal board, and an error message appears in the
message area.
This indication cannot be set to OFF.
For the error messages, see “Warning/Error Messages”
(page 126).
n Message area
Displays the status of auto setup, error messages, etc.
o Time code area
Displays the same time codes as those on the subdisplay.
When the SRW-1 is in a playback mode, only the time code
indication remains, and the other indications disappear.
The playback time code is displayed even if the time code
indication is set to OFF on the <VF DISPLAY> page of the
USER (OPERATION) menu.
For details, see “3-2-8 Confirmation of the Time Code and
Tape Remaining” (page 38).
Setting the basic status indications
The conditions for displaying the basic status indications
can be set on the <VF DISPLAY> page of the USER
(OPERATION) menu.
<VF DISPLAY> page
Item Setting
FPS Set to ON to obtain the frame rate indication
1.
FOCUS Set to ON to obtain the focus position
indication 3.
<VF DISPLAY> U01
FPS :
B
ON GAIN : ON
FOCUS : OFF SHUTT : ON
IRIS : OFF UNIT : deg
ZOOM : OFF BATT12: ON
ND : ON BATT24: OFF
5600K : OFF REC : ON
WHITE : OFF TAPE : OFF
TC : OFF
MESSAG: ALL