Filter
Top Products
1-36
DXC-D30WS/P(E)/V1
58
Chapter 4 Viewfinder Screen Indications and Menus
Chapter 4 Viewfinder Screen Indications and Menus
Advanced menu page 4
PAGE 4(NEXTm$ PREVm4)
MARKER:CENT/90%
mZEBRA:1
ZEBRA1:70IRE
VF SDTL:±0
VF TALLY: 2
EXIT MENU (YESm4)
×
a) For DXC-D30P: 70%
Viewfinder Advanced Menu
a)
Advanced menu page 3
PAGE 3(NEXTm$ PREVm4)
mAWB MEM:2
TONE:OFF
BARS:SMPTE
REMOTE1:REC
REMOTE2:MARK
BAUD RATE:38400
EXIT MENU (YESm4)
a) For DXC-D30P: EBU75
a) For more information about a connectable switch,
contact your Sony dealer.
Item
AWB MEM
Selects whether or not to
make the FILTER knob
settings (1 to 4) correspond
to separate white balance
adjustment values stored in
memory.
2 (normal value): No
correspondence with FILTER
knob settings. Only two
adjustment values (A and B)
are stored in memory.
2 × 4FL: Correspondence
with FILTER knob settings.
Each of the four knob
settings can be used to set A
and B adjustment values, for
a total of eight settings.
TONE
Selects whether or not to
output a 1-kHz audio signal
with the color bars when the
OUTPUT/DL/DCC+ has
been set to BARS.
ON (normal value): Output
audio signal.
OFF: Do not output audio
signal.
BARS
Selects normal width or
narrower width for color
bars.
SMPTE (normal value for
DXC-D30): Normal width
EBU75 (normal value for
DXC-D30P): EBU 75%
EBU100 (for DXC-D30P):
EBU 100%
SPLIT (for DXC-D30P): Not
for normal operation
SNG: Narrower than normal
(used for satellite
communications, etc.)
REMOTE1
Sets a function for position 1
of a switch connected to the
REMOTE1 connector.
a)
REC (normal value):
Specifies recording start/stop
MARK: Specifies a Mark IN/
OUT point.
CUE: Specifies a cue point.
NG: Specifies NG/OK.
REMOTE2
Sets a function for position 2
of a switch connected to the
REMOTE1 connector.
a)
9600, 38400 (normal value)
REC: Specifies recording
start/stop.
MARK (normal value):
Specifies a Mark IN/OUT
point.
CUE: Specifies a cue point
NG: Specifies NG/OK.
Settings
BAUD RATE
Sets a baud rate for a
computer connected to the
REMOTE connector 1 (to be
supported in future version).
Item
MARKER
Selects ON/OFF setting for
center marker, size setting
(percentage of viewfinder
screen area), and display
ON/OFF setting.
CENT/90% (normal value):
Displays center marker and
safety zone marker at 90%
size.
CENT/80%: Displays center
marker and safety zone
marker at 80% size.
90%: Displays only safety
zone marker at 90% size.
80%: Displays only safety
zone marker at 80% size.
CENT: Displays only center
marker.
ZEBRA
Selects type of zebra pattern
display.
1 (normal value): Displays
the zebra pattern over parts
having a video level.
between 70 and 90 IRE (or
70 and 90%).
Use the next item (ZEBRA1)
to select the base level.
2: Displays the zebra pattern
over parts having video
levels of 100 IRE or above
( or 100% or above).
1/2: Dual display (both 1
and 2)
ZEBRA1
Sets base level for zebra
pattern 1.
70 IRE (normal value) to 90
IRE or 70% (normal value)
to 90%
Can be set for each IRE
step or 1% step.
VF S DTL
Sets the detail level of
images on the viewfinder
screen (displayed only when
the DXF-501/501CE/601/
601CE viewfinder is
attached).
–99 to +0 (normal value) to
+99
Negative values set softer
edges and positive values
set sharper edges.
×1: Uses only the upper
REC/TALLY indicator.
×2 (normal value): Uses
two REC/TALLY indicators.
VF TALLY
Selects whether or not to use
more than one REC/TALLY
indicators in the viewfinder
(displayed only when the
DXF-701/701CE viewfinder
is attached).
Settings
a)
Chapter 4 Viewfinder Screen Indications and Menus
59
Chapter 4 Viewfinder Screen Indications and Menus
Advanced menu page 5
PAGE 5(NEXTm$ PREVm4)
mSS IND:ALWAYS
LL IND:ON
MIC IND:ON
IRIS IND:ON
GAIN IND:ON
FILTER IND:ON
EXIT MENU (YESm4)
Advanced menu page 6
PAGE 6(NEXTm$ PREVm4)
mAUDIO IND:ON
TAPE IND:ON
TC IND:ON
ID IND:OFF
ID SET:µ
( )
EXIT MENU (YESm4)
Item
Settings
SS IND
Selects the mode for
showing the shutter setting
when displaying the normal
indications.
3SEC: Displays shutter
setting for three seconds only
when the setting has been
changed.
ALWAYS (normal value):
Displays the shutter setting at
all times.
LL IND
Selects whether or not to
show the LOW LIGHT
indication on the normal
indications when inadequate
lighting is detected.
ON (normal value):
Displays.
OFF: Not display.
MIC IND
Selects whether or not to
show the camera
microphone output
indication on the normal
indications.
ON (normal value):
Displays.
OFF: Not display.
IRIS IND
Selects whether or not to
show the lens’s F-stop value
(iris indication) on the
normal indications. The F-
stop value is always
displayed when in EZ mode.
ON (normal value):
Displays.
OFF: Not display.
GAIN IND
Selects whether or not to
always show the gain
setting indication on the
normal indications.
ON (normal value): Always
displays.
OFF: displays for two
seconds only when the
setting has been changed.
FILTER IND
Selects whether or not to
always show the FILTER
knob setting indication on
the normal indications.
The FILTER knob setting
indicator is always displayed
when in EZ mode.
ON (normal value): Always
displays.
OFF: Displays for two
seconds only when the
setting has been changed.
Item
Settings
AUDIO IND
Selects whether or not to
show the audio level
indication on the normal
indications (valid only when
the DSR-1/1P or PVV-3/3P
is connected).
ON (normal value):
Displays.
OFF: Not display.
TAPE IND
Selects whether or not to
show the VTR’s remaining
tape indication on the normal
indications. (valid only when
the DSR-1/1P or PVV-3/3P
is connected).
ON (normal value):
Displays.
OFF: Not display.
TC IND
Selects whether or not to
show the time data indication
on the normal indications
(valid only when the DSR-1/
1P or PVV-3/3P is
connected).
ON (normal value):
Displays.
OFF: Not display.
ID IND
Selects whether or not to
display the camera ID when
displaying color bars.
ON (normal value):
Displays.
OFF: Not display.
ID SET
Sets the camera ID (up to
eight characters, including
alphanumerics, symbols,
and spaces).
See “To set the camera ID”
on next page.