Filter
Top Products
1-40
DXC-D30WS/P(E)/V1
66
Chapter 4 Viewfinder Screen Indications and Menus
Chapter 4 Viewfinder Screen Indications and Menus
Setup Files
3
Press the UP/ON button to store the file. To abort
the save operation, press the DOWN/OFF button
(the screen returns to the screen shown in step 2).
The tape automatically rewinds and recording
starts.
The display changes as shown below, which
includes color bars. (“CAN NOT WRITE”
appears on the screen if no tape is loaded or if the
loaded tape is write-protected.)
PAGE12(NEXTm$ PREVm4)
FILE STORE
FILE:*FILMLIKE
mDESTINATION FILE
TAPE
EXIT MENU (YESm4)
After the settings are stored, the following display
appears.
PAGE12(NEXTm$ PREVm4)
FILE STORE
FILE:*FILMLIKE
DESTINATION FILE
TAPE
mSTORE FILE?
DONE
EXIT MENU (YESm4)
Chapter 4 Viewfinder Screen Indications and Menus
67
Chapter 4 Viewfinder Screen Indications and Menus
Using SetupNavi and SetupLog with the DSR-1/1P
The SetupNavi function records the setup menu and
setup files onto a tape, so that the same settings can be
called up and used again or copied to another camera.
The SetupLog function records a camera settings every
few seconds at shooting and displays the recorded data
in the viewfinder during playback.
Note on using an RM-M7G Remote Control Unit
When an RM-M7G is connected to the camera head,
you can use neither the SetupNavi function nor the
SetupLog function.
To make it possible to use these functions, power OFF
the camera head after disconnecting the RM-M7G,
then power ON the camera head again.
Setting up the camera Using
Data Recorded on Tape
The procedure to replace camera’s menu settings with
settings recorded onto video tape is described here.
1
Connect the DSR-1/1P and insert the cassette onto
which the data was recorded. Set the SETUP
switch to FILE, then set the POWER switch to ON
while holding down the UP/ON button.
Advanced menu page 1 appears.
PAGE 1(NEXTm$ PREVm4)
mALL RESET
(YESm4)
EXIT MENU (YESm4)
2
Repeatedly press down on the MENU/STATUS
switch until advanced menu 13 appears.
For details of menu operation, see “Advanced Menu
Operations” (page 57).
PAGE13(NEXTm$ PREVm4)
SETUP NAVI
TAPEmCAMERA
mRECALL DATA
(YESm4)
EXIT MENU (YESm4)
”NO TAPE” is displayed if you neglected to load a
cassette.
3
Press the UP/ON button to call up the data
recorded on the tape. (Press the DOWN/OFF
button to cancel).
The display changes as follows and the call up
operation begins.
PAGE13(NEXTm$ PREVm4)
SETUP NAVI
TAPEmCAMERA
mCANCEL TO RECALL?
(YESm$)
SETUP NAVI
MY FILE
EXIT MENU (YESm4)
To abort the call up operation while in progress
Press the DOWN/OFF button.
The following display appears.
PAGE13(NEXTm$ PREVm4)
SETUP NAVI
TAPEmCAMERA
mSURE TO RECALL?
(YESm4)
EXIT MENU (YESm4)
4
Press the UP/ON button.
After the data has been read, the following display
appears.
PAGE13(NEXTm$ PREVm4)
SETUP NAVI
TAPEmCAMERA
mDONE
EXIT MENU (YESm4)
The previous menu settings are overwritten by the
data recorded on the tape.
5
Change the menu settings if necessary.
Name of data
being called up