Filter
Top Products
1-41
DXC-D30WS/P(E)/V1
68
Chapter 4 Viewfinder Screen Indications and Menus
Chapter 4 Viewfinder Screen Indications and Menus
Using SetupNavi and SetupLog with the DSR-1/1P
Recording the Menu Settings
onto a Tape
1
Connect the DSR-1/1P and load the tape onto
which the settings are to be recorded. Turn the
camera power on.
2
Make your basic menu settings.
For details of this operation, see “Basic Menu
Operations” (page 51).
3
Again, set the POWER switch to ON while
holding down the UP/ON button.
4
Make your advanced menu settings.
For details of this operation, see “Advanced Menu
Operations” (page 57).
5
Access advanced menu page 14.
PAGE14(NEXTm$ PREVm4)
SETUP NAVI
CAMERAmTAPE
mSTORE DATA
(YESm4)
EXIT MENU (YESm4)
“NO TAPE” appears if you neglected to load a
cassette.
6
Press the UP/ON button.
The following display appears.
PAGE14(NEXTm$ PREVm4)
SETUP NAVI
CAMERAmTAPE
mSURE TO STORE?
(YESm4)
NAME SET :
(YESm4)
( )
EXIT MENU (YESm4)
7
Set the cursor to “NAME SET” and press the UP/
ON button to record the menu setting onto the tape.
(Press the MENU/STATUS switch to cancel.)
The cursor (→) changes to the text entry cursor
(↓).
PAGE14(NEXTm$ PREVm4)
SETUP NAVI
CAMERAmTAPE
SURE TO STORE?
(YESm4)
NAME SET :
µ
( )
EXIT MENU (YESm4)
8
Enter a name for the data.
Moving the text entry cursor: Press the MENU/
STATUS switch up to move the cursor to the
right, and press the MENU/STATUS switch
down to move the cursor to the left.
Selecting the character: Press the UP/ON or
DOWN/OFF button repeatedly until the desired
character appears.
9
After completing text entry, move the cursor to the
parenthesis position.
The display changes as follows.
PAGE14(NEXTm$ PREVm4)
SETUP NAVI
CAMERAmTAPE
SURE TO STORE?
(YESm4)
mNAME SET :
(YESm4)
MY FILE
EXIT MENU (YESm4)
10
Move the cursor to “SURE TO STORE?” and
press the UP/ON button to record the menu
settings onto the tape (press the MENU/STATUS
switch to cancel).
The display changes as follows and the data
recording begins.
PAGE14(NEXTm$ PREVm4)
SETUP NAVI
CAMERAmTAPE
mCANCEL TO STORE
(YESm$)
SETUP NAVI
MY FILE
EXIT MENU (YESm4)
Name of data
being recorded
Chapter 4 Viewfinder Screen Indications and Menus
69
Chapter 4 Viewfinder Screen Indications and Menus
To abort the data recording while in progress
Press the DOWN/OFF button.
After the data has been recorded, the following display
appears.
PAGE14(NEXTm$ PREVm4)
SETUP NAVI
CAMERAmTAPE
mSTORE DATA
DONE
EXIT MENU (YESm4)
Viewing SetupLog Data
1
Connect the DSR-1/1P and load the tape that
contains the recording to be viewed. Turn the
camera power on.
2
Play back the tape.
For details of playback operation, see the operating
instructions for the DSR-1/1P.
3
Press the MENU/STATUS switch up to the
STATUS side.
The display changes to page 1 of the status display.
PLA
TCR 2:34 56:1:00
A
TW
EZ
E
VS
R
ND
0849
224MP
:
U FILE: STD
+ : OFF
N
P
DTL : OFF
T
C
I
E
C
K
S
D
S
T : A 5600EIHW
R S : SPOT LII.A
Y
P LOG 1/3UTES
18
42
Each time you press upward the MENU/STATUS
switch, the status display cycles through the status
pages and playback display in the order: page 2,
page 3, the playback display (containing the
current settings), and page 1.
Status display (page 2)
PLA
TCR 2:34 56:1:00
A
TW
EZ
E
VS
08 4429
224MP
:
Y
P LOG 2/3UTES
RS :±0
EV : ±10
LCK :±0
ECH :±0
I
L
A
T
: OFF
I
L
B
R
.
T
.
T
S
A
D
M
S
S
R
ND
18
Status display (page 3)
PLA
TCR 2:34 56:1:00
A
TW
EZ
E
VS
08 4429
224MP
:
Y
P LOG 3/3UTES
AMA :±0
T LEV : +50
REQ : M
N
M
L
F
HUE : ±0
G
D
L
I
.
T
K
M
V
D
S
N SAT : ±0IKS
: ±0 EUH
: ±0TAS
R
ND
18
Notes
•SetupLog data is not recorded while SetupNavi data
or a setup file is being recorded onto a tape. (If you
play back a tape containing SetupNavi data or a setup
file, the data displayed in the setup display is not the
SetupLog data of the playback picture.)
•In the following cases, changed settings that were not
recorded may appear as blank settings.
– SetupLog data is overwritten at intervals of a few
seconds during recording. If the settings are
changed frequently for certain items, it may not
always be recorded in time.
– If the recording time is very short, recording may
be ended before all of the data has been
overwritten.
Settings during
recording