Filter
Top Products
1-38
DXC-D30WS/P(E)/V1
62
Chapter 4 Viewfinder Screen Indications and Menus
Chapter 4 Viewfinder Screen Indications and Menus
3
Move the cursor to SELECT FILE and use the UP/
ON button or the DOWN/OFF button to select the
desired file.
Press the UP/ON button or DOWN/OFF button
repeatedly until the desired file name is displayed.
FILE: *FL
mSELECT FILE
FILMLIKE
CHG FILE
(YESm4)
4
Move the cursor to CHG FILE and press the UP/
ON button.
The display changes as shown below and the
selected file is called up.
FILE: *FL
SELECT FILE
FILMLIKE
mCHG FILE
DONE
You can also call up these files via a similar operation
in advanced menu page 9. In this page, a file recorded
onto a tape can also be called up (when using the
DSR-1/1P).
For details, see “To call up files recorded onto a tape (when
using the DSR-1/1P)” (page 63).
USER1 to USER3 User setup files (set to STD at
shipping)
Setup Files
You can use setup files to reproduce a particular
configuration of settings. You can also revise the
contents of setup files.
There are eight types of setup files, of which five are
factory preset setup files and the other three are user
files.
Note on using an RM-M7G Remote Control Unit
When an RM-M7G is connected to the camera head,
the setup file function cannot be used.
To make it possible to use this function, power OFF
the camera head after disconnecting the RM-M7G,
then power ON the camera head again.
Calling up a Setup File
This describes how to call up a setup file and use it to
replace the current menu settings.
1
Set the SET UP switch to FILE.
The camera head is set according to the currently-
selected file data.
2
Access basic menu page 4.
FILE: *FL
mSELECT FILE
FL
CHG FILE
(YESm4)
a) An asterisk (*) appears in front of any factory
preset file whose contents have been revised at
least once.
SET UP switch
Current file
a)
Selected file
File
Description
STD
Settings for shooting under
standard conditions
HI SAT Settings for making pictures
vivid
FL Settings for shooting under
fluorescent lighting
FILMLIKE Settings for making pictures like
ones shot by film camera
SVHS/VHS
Settings to optimize camera
image for recording and
playback characteristics of S-
VHS, VHS, or Hi-8 tape
Chapter 4 Viewfinder Screen Indications and Menus
63
Chapter 4 Viewfinder Screen Indications and Menus
To call up files recorded onto a tape (when
using the DSR-1/1P)
First, connect the DSR-1/1P to the camera head and
load the cassette that contains the recorded files.
1
Set the SET UP switch to FILE.
2
Access advanced menu page 9.
PAGE 9(NEXTm$ PREVm4)
FILE RECALL
FILE:*FL
mSELECT FILE
FL
CHG FILE
(YESm4)
EXIT MENU (YESm4)
3
Move the cursor to SELECT FILE and use the UP/
ON button or the DOWN/OFF button to select
TAPE.
PAGE 9(NEXTm$ PREVm4)
FILE RECALL
FILE:*FL
mSELECT FILE
TAPE
CHG FILE
(YESm4)
EXIT MENU (YESm4)
4
Move the cursor to CHG FILE and press the UP/
ON button.
The screen appears as shown below.
PAGE 9(NEXTm$ PREVm4)
FILE RECALL
FILE:*FL
mSELECT FILE
TAPE
READY TAPE?
(NOm$ YESm4)
EXIT MENU (YESm4)
5
Press the UP/ON button to call up the file. To
abort the call up operation, press the DOWN/OFF
button (the display returns to the one shown in step
3).
During the call up operation, the following display
appears.
PAGE 9(NEXTm$ PREVm4)
FILE RECALL
FILE:*FL
SELECT FILE
TAPE
SETUP FILE
EXIT MENU (YESm4)
When the call up operation ends, the display
changes as shown below.
PAGE 9(NEXTm$ PREVm4)
FILE RECALL
FILE:USER2
SELECT FILE
TAPE
mCHG FILE
DONE
EXIT MENU (YESm4)
The settings of the camera head are now replaced
by the settings in the called file.
Name of file
recorded onto
tape