Filter
Top Products
2-6
DVW-790WS/709WS/707
DVW-790WSP/709WSP/707P P2V1
No. Page Item Setup Description
13 FUNCTION 2/2 DCC FUNCTION FIX/[DCC]/ADP.K
Selects the DCC function modes when the DCC switch is set to ON.
SEL
DCC : Normal mode
(Dynamic range is set by the DCC ADJUSTMENT page.)
FIX : Knee is corrected by the fixed dynamic range of 600%.
ADP.K: Adaptive mode
Detects an object which is occupying the largest area
of a picture and automatically adjusts the knee point
and knee slope to obtain the optimum level for the object.
REAR BNC OUT [VBS]/SDI/OFF Selects the signal to be output from the rear panel VIDEO OUT
connector when the SDI output board BKDW-702 is installed.
VBS : Outputs the composite video signal.
SDI : Outputs the SDI signal.
OFF : Set to OFF when power saving is desired.
VTR MODE ON/[OFF] Set to ON when an external VTR is controlled by the VTR START
button as it is interlocked with the DVW, when an external VTR is
connected via the CA-702.
REC INHIBIT [ON]/OFF Set to OFF when you use a built-in VTR for recording even though
CCU is connected via CA-705/755.
Note : When this setup is set to OFF, a viewfinder can not be
powered on.
ASSIGNABLE SW [OFF]/RET/REC/ Selects function of the ASSINABLE button.
TURBO/
OFF : No function assigned
AUDIO/ATW/
RET : RET button
LOOPR/F.SHT
REC : VTR START button
TURBO : TURBO GAIN button
AUDIO : The ON/OFF switch of the function to display the
AUDIO source on VF for each channel.
ATW : The ON/OFF switch of the ATW function
LOOPR : The ON/OFF switch of the loop recording function.
(This item is displayed only when the picture cache
board BKDW-703 is installed.)
F. SHT : The ON/OFF switch of the frame shutter function.
(This item is displayed only when the frame shutter unit
BKDW-705 is installed.)
14 WIDE SCREEN Note : This page is displayed only in DVW-790WS/790WSP/
709WS/709WSP only
16:9/4:3 MODE [16:9]/4:3 Sets the aspect ratio of the video signal output from the VIDEO
OUT and TEST OUT connectors.
VF ASPECT [AUTO]/4:3/ Sets the aspect ratio on the viewfinder.
16:9A/16:9B AUTO : Sets the aspect ratio set by 16:9/4:3 MODE setting.
4:3 : Sets the aspect ratio to 4:3 regardless of 16:9/4:3 MODE
setting.
16:9A :
Sets the aspect ratio to 16:9 regardless of 16:9/4:3 MODE
setting (displays the area of 4:3 mode with the marker).
16:9B :
Sets the aspect ratio to 16:9 regardless of 16:9/4:3 MODE
setting (video level is cut in half out of the safety zone
area on the VF screen).
BOX/4:3/14:9 [BOX]/4:3/14:9 Sets the function of the box cursor.
LIMITS
BOX : Operates as the normal cursor function.
4:3 : Displays the 4:3 area when the 16:9/4:3 MODE set to 16:9.
14:9 : Displays the 14:9 area when 16:9 is selected by the above
described 16:9/4:3 MODE.
16:9 BARS ID ON/[OFF] Turns ON/OFF the function of adding the 16:9 display to the built-
in color bar when 16:9 is selected by the above described 16:9/4:3 MODE.
16:9 VF ID ON/[OFF]
Turns ON/OFF the function of adding the 16:9 display to the VF screen
when 16:9 is selected by the above described 16:9/4:3 MODE.
2-1. Service Mode