Filter
Top Products
Setting the Status Display on the Viewfinder Screen and the LCD Monitor
173
Chapter 6 Menu Displays and Detailed Settings
a) This is also displayed for about 3 seconds when the
SHUTTER selector is set to ON.
Changing the display mode
1 Display the VF DISP 1 page of the
OPERATION menu, and press the
MENU knob.
For details on menu operations, see “Basic
menu operations” on page 163.
2 Select VF DISP MODE, and press the
MENU knob.
3 Select the desired display mode, and
press the MENU knob.
Switch the display of the center and safety zone
markers on or off, and select whether the area
indicated by the safety zone marker is 80%, 90%,
92.5%, or 95% of the screen area.
(How to select an item in the menu screen: Turn
the MENU knob to move b to the desired item.)
1 Display the MARKER 1 or MARKER 2
page of the OPERATION menu, and
press the MENU knob.
For details on menu operations, see “Basic
menu operations” on page 163.
2 Select the desired item, and press the
MENU knob.
You can set the following items on the
MARKER 1 and MARKER 2 pages.
MARKER 1 page
a) The ASPECT MASK setting affects the
viewfinder and LCD monitor display. In the
following cases, it also affects the VBS signal.
• When TEST OUT SELECT on the OUTPUT 1
page is set to VBS.
• When both TEST OUT SUPER on the
OUTPUT 1 page and SUPER(MARKER) on
the SUPER IMPOSE page are set to ON.
ASPECT MASK is ignored for displays in the
viewfinder when the following are true.
• TEST OUT SELECT on the OUTPUT 1 page
is set to HD-Y, and a cable is connected to the
TEST OUT connector.
• TEST OUT SELECT on the OUTPUT 1 page
is set to HD-Y, and TEST OUT SAVE on the
POWER SAVE page is set to OFF.
When the gain
setting has been
changed
GAIN: n (where n
= –6dB, –3dB, 0dB,
3dB, 6dB, 9dB,
12dB, 18dB, 24dB,
30dB, 36dB, 42dB)
NNY
When the setting of
the WHITE BAL
switch has been
changed
WHITE: n (where n
= A CH, B CH,
PRESET) or ATW:
RUN
NNY
When the
OUTPUT/DCC
switch has been set
to DCC ON or OFF
DCC: ON (or OFF) N Y Y
When the shutter
speed and mode
setting has been
changed
a)
:SHUTTER:
1/100 (or 1/125,
1/250, 1/500, 1/
1000, 1/2000, ECS)
NYY
When the black or
white balance has
been adjusted
E.g. AWB : OK N Y Y
Setting the marker display
Message display
condition
Message Display
mode
setting
1 2 3
Item Description
MARKER To hide all markers, set to
“OFF”.
CENTER To display the center marker,
set to “ON”.
CENTER
MARK
Selects the position of the
center marker.
SAFETY
ZONE
To display the safety zone, set
to “ON”.
SAFETY
AREA
Selects the safety zone range
(80%, 90%, 92.5% or 95%).
ASPECT To display the aspect marker,
set to “ON”.
ASPECT
SELECT
Selects the aspect mode (15:9/
14:9/13:9/4:3/1.85/2.35).
ASPECT
MASK
a)
To make the areas out of the
selected aspect marker dimmer,
set to “ON”.
ASPECT
MASK LVL
To set the mask level, when the
ASPECT MASK is set to
“ON”.
100 %
MARKER
To display the effective pixel
area, set to “ON”.