Filter
Top Products
155
Maintenance and Inspections: Warning System
Maintenance and Inspections
The following error codes are displayed in the display window if an error occurs in the camera:
Confirm the type of warning and refer to the details in the [Warning Description Tables] (page 153) for countermeasures.
11. P2 Card Nearly Full
Display window
indication
One of the bars for remaining MEDIA capacity
starts blinking.
WARNING lamp
Blinks once per second while recording
continues.
Tally lamp
Blinks once per second while recording
continues.
Viewfinder
The P2 card remaining capacity indicator blinks.
Warning tone
Beeps once per second while recording
continues.
Warning
description
The total remaining capacity of all the P2
cards is two minutes or less.
Recording/
playback
operation
Continues to operate.
Countermeasures
Replace the cards. If there is an empty card
slot, insert a new card.
12. P2 Card Error
Display window
indication
Displays “00:00:00:11” in the time code
display. The window continues to flash until
the next operation, even after stopping record
and playback.
WARNING lamp
If the error occurs during recording, the lamp
flashes four times per second for a period of
about three seconds. The lamp does not light
if the error occurs during playback.
Tally lamp
If the error occurs during recording, the lamp
flashes four times per second for a period of
about three seconds. The lamp does not light
if the error occurs during playback.
Viewfinder
A flashing “CARD ERR
¢
” appears. In the actual
indication the
¢
is replaced by the slot number of
the P2 card that triggered the error.
Warning tone
If the error occurs during recording, the tone
sounds four times per second for a period of
about three seconds. The tone does not
sound if the error occurs during playback.
Warning
description
An error has occurred while recording data to
or playing data from a P2 card.
Recording/
playback
operation
Stop recording or playback. After recording is
stopped, the P2 card where error occurs is
write protected.
Countermeasures
Replace the affected P2 card.
13. FAN STOP
Display window
indication
No display.
WARNING lamp Blinks 4 times per second.
Tally lamp
No display.
Viewfinder
The FAN STOP indicator blinks while
recording continues.
Warning tone It does not sound.
Warning
description
The fan is at rest because something is wrong
with it. Alternatively, the FAN MODE item is
set to “OFF”. The menu item FAN MODE is
found in the <OPTION> screen on the
OPTION MENU page.
Recording/
playback
operation
If the camera-recorder operates with the fan
stopped, then the temperature inside rises.
While the camera-recorder continues to
operate, clips may not be recorded or played
back properly.
Countermeasures
Immediately stop using the camera-recorder
and consult your distributor.
Error Codes
Code No. Description Type of warnings
E-11 Video initialisation error 1. System Errors
E-27 Recording control error 1. System Errors
E-30 P2 card removal error 2. Card removal error
E-34 LCD microcontroller error 1. System Errors
E-38 P2 streaming microcontroller error 1. System Errors
E-3F Microprocessor error in the camera control circuit. 1. System Errors
E-40 Image sequence, GENLOCK input signal or SDI input signal error
5. Image Sequence Error, 6. Corruption of Standard Signal
E-63 Something is wrong with the system control microprocessor. 1. System Errors
E-6F Reference signal error. 1. System Errors
00:00:00:11 Errors such as recording to P2 card error 7. Recording Error, 8. Number of Clips Exceeded,
12. P2 Card Error
AJ-HPX3100G(VQT3A79)_E.book 155 ページ ２０１０年９月１７日 金曜日 午後９時２１分