Filter
Top Products
41
Recording and Playback: Interval Recording
Recording and Playback
After setting the ONE SHOT mode of INTERVAL REC, follow
these steps:
1 Following basic operations of shooting and
recording according to “Basic Procedures”,
lock the camera securely.
2 Press the REC button.
z The AJ-HPX3100 automatically goes into ONE
SHOT pause mode after the specified REC TIME.
z Performs recording for the duration specified under
the REC TIME option by pressing the REC button,
and returns to ONE SHOT pause mode.
3 Press the STOP button.
The video stored in memory are generated as one clip.
Even during ONE SHOT mode, clips will not be generated
on the P2 card until the STOP button is pressed. Press the
STOP button, and stop ONE SHOT mode operation.
When replacing the P2 card, check the access LED, etc. to
make sure that access has been terminated before
removing the P2 card.
zSet the menu option INTERVAL REC MODE to “OFF”.
When INTERVAL REC HOLD is set to [OFF], the mode
returns to ordinary recording mode if the POWER switch of
the unit is turned OFF.
If INTERVAL REC HOLD is set to [ON], the ONE SHOT
mode will not change even if the POWER switch is turned
OFF.
z
Sound
Interval recording does not record audio.
z
Record/Playback Buttons
During interval recording, all operation buttons other than
STOP (REW, FF, PLAY/PAUSE) are disabled.
z
If the power is turned off during recording
If the AJ-HPX3100 is turned off during interval recording,
the video stored in memory is recorded onto the P2 card,
and then the camera automatically turns off.
z
Time code indication
When recording starts, the time code (TCG) display may
not update until the unit recognizes the P2 card.
z
Removing cards
During INTERVAL REC mode operation, the P2 card
access LED for the inserted P2 card blinks in orange. Do
not remove the P2 card during this status. If you should
remove the card accidentally, restore clips. However, even
if the clips are restored, the last 3 to 4 seconds up to a
maximum of about 10 seconds of the recording may be
lost if the P2 card is removed while recording onto multiple
P2 cards. For more information on how to fix clips, see
[Restoring Clips] (page 126).
z Operating mode limitations
INTERVAL REC function does not work when:
the LOOP REC MODE menu option is set to “ON”.
the ONE CLIP REC MODE menu option is set to
“ON”.
Native mode, 24P or 24PA mode is selected in the
REC FORMAT or CAMERA MODE menu option.
The REC SIGNAL menu option is set to “SDI”.
> [Recording Setting and Operation Mode] (page 46)
z
Thumbnail operation and menu operation
Thumbnail operation does not work during the INTERVAL
REC mode operation. Press the STOP button before
operating thumbnails.
When standby time is set to 1 minute or more or when in
ONE SHOT mode, the following restrictions apply even
though the menu can be operated during stand-by mode.
The respective settings or SYSTEM MODE, REC
SIGNAL, REC FORMAT, CAMERA MODE, AUDIO
SMPL RES, 25M REC CH SEL, and PC MODE cannot
be changed.
The respective settings for SD CARD READ/WRITE,
LENS FILE CARD R/W, READ USER DATA, READ
FACTORY DATA, reading SCENE FILE, and CAC FILE
CARD READ cannot be executed.
Shooting procedures for the ONE SHOT mode of
INTERVAL REC
To divide clips or to change the P2 card used for
recording
To stop the ONE SHOT mode of INTERVAL REC
A
t
A
B
t
B
Previous clip
Real-time video
Sound
Content on P2 card
One clip
REC TIME
(Recording
time=t)
iREC
start
Time
Axis
iREC
start
STOP
button
During INTERVAL REC mode general notes
AJ-HPX3100G(VQT3A79)_E.book 41 ページ ２０１０年９月１７日 金曜日 午後９時２１分