Filter
Top Products
Chapter 3 Recording and Playback
53
3-2 Recording
6
Turn the MENU knob until A. INT appears.
As you turn the MENU knob, the setting changes in
the following sequence: OFF y CACHE y A. INT
y M. INT.
When A. INT appears, the camcorder is in Auto
Interval Rec mode. The TALLY indicator (green) in
the viewfinder flashes (one flash/second) while the
camcorder is in this mode. Also, TAKE TOTAL
TIME, REC TIME and PRE-LIGHTING appear.
7
Press the MENU knob.
The z mark changes to a b mark and the ? mark
changes to a z mark.
8
Turn the MENU knob to move the b mark to “TAKE
TOTAL TIME” (see “Time required for shooting and
time required for recording on the disc” (page 54)).
9
Press the MENU knob.
The b mark on the left of “TAKE TOTAL TIME”
changes to a z mark and the z mark on the left of the
setting changes to a ? mark.
10
Turn the MENU knob until the desired setting of
“TAKE TOTAL TIME” appears.
As you turn the MENU knob, the setting of TAKE
TOTAL TIME changes in the following sequence:
5MIN y 10MIN y 15MIN y 20MIN y
30MIN y 40MIN y 50MIN y 1H y 2H y
3H y 4H y 5H y 7H y 10H y 15H y 20H
y 30H y 40H y 50H y 70H y 100H.
Here MIN means minutes (5MIN is 5 minutes) and H
means hours (1H is one hour).
11
Press the MENU knob.
The z mark changes to a b mark and the ? mark
changes to a z mark.
12
Turn the MENU knob to move the b mark to “REC
TIME”.
13
Press the MENU knob.
The b mark on the left of “REC TIME” changes to a
z mark and the z mark on the left of the setting
changes to a ? mark.
14
Turn the MENU knob until the desired time to be
recorded on the disc appears.
As you turn the MENU knob, the setting of REC
TIME changes in the following sequence: 5SEC y
10SEC y 15SEC y 20SEC y 30SEC y
40SEC y 50SEC y 1MIN y 2MIN y
.......85MIN.
Here SEC means seconds (5SEC is 5 seconds) and
MIN means minutes (1MIN is one minute).
You cannot set a REC TIME that is more than one
thirtieth of TAKE TOTAL TIME.
For example: When TAKE TOTAL TIME is set to 1H,
the maximum value of REC TIME is 2 MIN. (60
minutes divided by 30 gives 2 minutes.)
15
Press the MENU knob.
The z mark changes to a b mark and the ? mark
changes to a z mark.
16
Turn the MENU knob to move the b mark to “PRE-
LIGHTING”.
17
Press the MENU knob.
ASSIGN SW <1> : ATW
ASSIGN SW <2> : OFF
ASSIGN SW <3> : OFF
ASSIGN SW <4> : OFF
TURBO SW : TURBO
DF/NDF : DF
CACHE/INTVAL REC: A.INT
TAKE TOTAL TIME : 5MIN
REC TIME : 5SEC
PRE-LIGHTING : OFF
03 FUNCTION1 TOP
ASSIGN SW <1> : ATW
ASSIGN SW <2> : OFF
ASSIGN SW <3> : OFF
ASSIGN SW <4> : OFF
TURBO SW : TURBO
DF/NDF : DF
CACHE/INTVAL REC: A.INT
TAKE TOTAL TIME : 5MIN
REC TIME : 5SEC
PRE-LIGHTING : OFF
? 03 FUNCTION1 TOP
ASSIGN SW <1> : ATW
ASSIGN SW <2> : OFF
ASSIGN SW <3> : OFF
ASSIGN SW <4> : OFF
TURBO SW : TURBO
DF/NDF : DF
CACHE/INTVAL REC: A.INT
TAKE TOTAL TIME : 20M
REC TIME : 5SEC
PRE-LIGHTING : OFF
? 03 FUNCTION1 TOP
ASSIGN SW <1> : ATW
ASSIGN SW <2> : OFF
ASSIGN SW <3> : OFF
ASSIGN SW <4> : OFF
TURBO SW : TURBO
DF/NDF : DF
CACHE/INTVAL REC: A.INT
TAKE TOTAL TIME : 20M
REC TIME : 5SEC
PRE-LIGHTING : OFF
? 03 FUNCTION1 TOP