Filter
Top Products
162
Troubleshooting
Appendix
a) Displayed only when setup menu item 016 ALARM DISPLAY is set to
“on”.
b) Displayed only when setup menu item 016 ALARM DISPLAY is set to
“on” or “limit”.
Mixed REC! THIS DISC CANNOT BE RECORDED.
TWO OR MORE AUDIO OR VIDEO
FORMATS ARE RECORDED ON THE
DISC.
This appears if a disc containing clips recorded in
different recording formats is inserted while mixed
format recording mode is disabled. Enable mixed
format recording mode, or insert another disc.
Mixed REC!
b)
DISC CANNOT BE EDITED.
MIXED AUDIO/VIDEO MODE ON DISC.
This appears when an edit preset command is
received, but the inserted disc contains clips with
mixed recording formats.
Exchange the inserted disc for a disc that does not
contain clips with mixed recording formats.
Resolution THIS CLIP CANNOT BE ADDED.
THE CLIP’S RESOLUTION DOES NOT
MATCH THE CLIP LIST’S RESOLUTION.
Clips can be registered in clip lists only if their
resolution (number of system lines) matches the
resolution of clips in the clip list.
i.LINK!
b)
CANNOT EDIT AV MATERIAL WHEN
INPUT SIGNAL IS VIA i.LINK.
This appears when an edit preset command is
received, but “i.LINK” is selected as the input signal.
Under V INPUT on the P1 VIDEO page of the
function menu, select a signal other than “i.LINK”.
SD Input!
b)
CANNOT EDIT AV MATERIAL WHEN
INPUT SIGNAL IS VIA SD-SDI.
This appears when an edit preset command is
received, but the recording format is set to HD422
and “SDSDI” is selected as the video input signal.
Under V INPUT on the P1 VIDEO page of the
function menu, select “HDSDI”.
NON-AUDIO!
b)
AUDIO INSERT EDITING WITH
INDEPENDENT CHANNELS IS NOT
POSSIBLE.
CHANGE ‘NON-AUDIO INPUT’ IN
MAINTENANCE MENU FROM ‘DATA’ TO
‘AUDIO’.
This appears when digital audio signals are set to
“data” and an edit preset command is received for
individual channels in the audio input channel pairs
(CH1/2, CH3/4, CH5/6, CH7/8). To perform insert
editing of non-audio signals, always operate on
channel pairs.
If you want to perform insert editing of the audio of
individual channels from channel pairs, set
maintenance menu item M37: AUDIO CONFIG
>M372: NON-AUDIO INPUT to “audio”.
List Exists DISC CANNOT BE EDITED.
DELETE ALL CLIP LIST BEFORE
BEGINNING DESTRUCTIVE EDITING.
This appears when an edit preset command is
received but the inserted disc contains a clip list.
Exchange the disc for one that does not contain a clip
list, or delete all clip lists from the disc.
N/A Clip!
b)
CANNOT EDIT AV MATERIAL.
CHECK REC FORMAT IN CLIP.
This appears when an edit preset command is
received for an HD420 clip or another clip that cannot
be edited.
Check the recording format of the edit target clip (see
page 59).
Mode Err!
b)
CANNOT EDIT AV MATERIAL.
CHANGE ‘SNGL CLIP PB’ TO ‘OFF’ AND
‘REC MODE’ TO ‘NORMAL’ IN SETUP
MENU.
This appears when an edit preset command is
received but the unit is in Single Clip Playback mode,
Disc Exchange Cache mode, or Clip Continuous Rec
mode.
Set setup menu item 154 SINGLE CLIP PLAY MODE
to “off”, or set setup menu item 150 REC MODE to
“normal”.
N/A Disc!
b)
DISC CANNOT BE EDITED.
USE PFD23A OR PFD50DLA.
This appears when an edit preset command is
received, but linear editing is not possible for the
inserted disc.
Insert a disc that can be edited by linear editing (see
page 60).
Alarm message in time
data display area
Alarm message in video monitor screen Description/action