Filter
Top Products
86
Scene Selection (Clip List Editing)
Chapter 5 Operations in GUI Screens
To play a clip list, insert a disc into the unit, load the clip
list that you want to play, and press the PLAY button.
Clips are played according to the data in the clip list.
Creating and editing clip lists
The following table lists the steps in the creation and
editing of clip lists with the scene selection function. To
create a clip list, you always need to carry out the steps
inside the heavy lines. Other steps can be carried out as
required.
To reedit clip lists on the disc
Use the Load Clip List command to load the clip lists you
want to edit, and perform the steps 2 to 4 in the previous
section.
You can also delete clip lists on the disc.
For details, see “Managing clip lists” (page 90).
Clip lists can be created and edited even when the write
inhibit tab of the disc is set to recording disabled, and when
REC INH on the HOME page of the function menu is set
to ON. However, if you need to save the clip list, set write
inhibit tab and REC INH to enable recording before you
create or edit the clip list.
To add sub clips
You can add sub clips to clip lists from with the clip
thumbnail screen or the clip list thumbnail screen.
However, you must use the clip list thumbnail screen to
edit clip lists.
Adding sub clips from the clip thumbnail screen
The following procedure explains operations in the clip
thumbnail screen. You can proceed in the same way in the
expand thumbnail screen and the chapter thumbnail
screen. Expanded blocks are added as sub clips in the
expand thumbnail screen, and chapters are added as sub
clips in the chapter thumbnail screen.
See page 73 for more information about thumbnail screen
operations.
1
In the clip thumbnail screen, select the clip that you
want to add as a sub clip (multiple selections possible).
2
Display the Thumbnail Menu.
3
Select Add Sub Clips, and then press the PUSH
SET(S.SEL) knob.
The Add Sub Clip screen appears.
The clip(s) selected in step 1 appear in the upper part
of this screen, and the clip list appears in the lower
Scene Selection window. The I cursor in the Scene
Selection window indicates the location where the
currently selected sub clip(s) will be inserted.
To display the total duration after addition of the
selected clip
Press the SHIFT button.
4
In the Scene Selection window, move the I cursor to
the location where you want to insert the clip. (The
existing thumbnails arrange themselves to the left and
right of the I cursor.)
5
Press the PUSH SET(S.SEL) knob.
The selected clip is inserted as a sub clip and a “+”
mark appears on the thumbnail in the Scene Selection
window.
1 Add sub clips: Use the Add Sub Clips command to add
the clips you want to use to a clip list. You can add
up to 300 sub clips to one clip list.
This operation can be carried out in the following
thumbnail screens.
• Clip thumbnail screen
• Expand thumbnail screen
• Chapter thumbnail screen
• Clip list thumbnail screen
2 Change the sub clip order: Use the Move Sub Clips
command to change the order of sub clips in a clip
list.
Delete sub clips: Use the Delete Sub Clips command
to delete specified sub clips from a clip list.
Trim sub clips: Use the Trim Sub Clip command to
adjust the In and Out points of a sub clip. This
function can also be used to adjust the overall
duration of the clip list.
Set the start timecode: Use the Set Start Time Code
command to set the timecode at the start of a clip
list.
3 Play the clip list: Use the PLAY button and other
playback controls to play the current clip list and
check its contents.
4 Save the clip list: Use the Save Clip List or Save Clip
List as… command to save the newly created clip
list to the disc.
Note
TOTAL
00:13:48:24
Add Sub Clip 017/035002
Scene Selection
TC 00:30:25:11
TC 00:24:24:29
TC 00:30:40:13
TC 00:24:34:27
TC 01:01:28:25
TC 00:24:46:22
TC 00:09:43:14
TC 00:24:56:24