Filter
Top Products
TELEDYNE API
Table of Contents M703E Calibrator Operator’s Manual
6.2. Overview of Operating modes .....................................................................................................................37
6.3. STANDBY Mode ..........................................................................................................................................38
6.4. General Information about the GENERATE mode ......................................................................................39
6.4.1. GENERATE AUTO: Basic Generation of Calibration Gas................................................................39
6.5. AUTOMATIC CALIBRATION SEQUENCES...............................................................................................40
6.5.1. SETUP SEQ: Programming Calibration Sequences.........................................................................40
6.5.1.1. Activating a Sequence from the M703E Front Panel .....................................................................41
6.5.1.2. Naming a Sequence.......................................................................................................................42
6.5.1.3. Setting the Repeat Count for a Sequence .....................................................................................43
6.5.1.4. Using the M703E’s Internal Clock to Trigger Sequences...............................................................44
6.5.1.5. Setting Up Control Inputs for a Sequence......................................................................................47
6.5.1.6. Setting Up Control Outputs for a Sequence...................................................................................48
6.5.1.7. Setting the PROGRESS Reporting Mode for the Sequences........................................................49
6.5.2. Adding Sequence Steps ........................................................................................................................50
6.5.2.1. The Generate Step.........................................................................................................................51
6.5.2.2. The STANDBY Step.......................................................................................................................52
6.5.2.3. The DURATION Step .....................................................................................................................52
6.5.2.4. The EXECSEQ Step.......................................................................................................................53
6.5.2.5. The CC OUTPUT Step...................................................................................................................54
6.5.2.6. Deleting or Editing an Individual Step in a Sequence ....................................................................55
6.5.3. Deleting a Sequence .............................................................................................................................56
6.6. SETUP CFG............................................................................................................................................57
6.7. SETUP CLK.............................................................................................................................................58
6.7.1. Setting the internal Clock’s Time and Day.............................................................................................58
6.7.2. Adjusting the internal Clock’s speed......................................................................................................59
6.8. SETUP PASS..........................................................................................................................................60
6.9. SETUP DIAG TEST CHAN OUTPUT: Using the TEST Channel Analog Output...............................62
6.9.1. Configuring the TEST CHANNEL Analog Output..................................................................................62
6.9.1.1. The Analog I/O Configuration Submenu. .......................................................................................62
6.9.1.2. Selecting a Test Channel Function to Output ................................................................................64
6.9.1.3. TEST CHANNEL VOLTAGE RANGE Configuration......................................................................66
6.9.1.4. Turning the TEST CHANNEL Over-Range Feature ON/OFF........................................................67
6.9.1.5. Adding a Recorder Offset to the TEST CHANNEL ........................................................................68
6.9.2. TEST CHANNEL CALIBRATION ..........................................................................................................69
6.9.2.1. Enabling or disabling the TEST CHANNEL Auto-Cal Feature.......................................................69
6.9.2.2. Automatic TEST CHANNEL Calibration.........................................................................................70
6.9.2.3. Manual Calibration of the TEST CHANNEL configured for Voltage Ranges.................................72
6.9.3. AIN Calibration.......................................................................................................................................74
6.10. SETUP MORE VARS: Internal Variables (VARS)............................................................................75
6.11. Operating the M703E Calibrator as an O
3
Photometer.............................................................................77
6.11.1. Set up for Operating the M703E as an O
3
Photometer .......................................................................77
6.12. SETUP LVL: Setting up and using LEADS (Dasibi) Operating Levels .................................................79
6.12.1. General Information about LEADS LEVELS .......................................................................................79
6.12.2. Dot commands.....................................................................................................................................79
6.12.3. Levels...................................................................................................................................................80
6.12.4. Activating an existing LEVEL...............................................................................................................80
6.12.5. Programming New LEVELS ................................................................................................................81
6.12.5.1. Creating a GENERATE LEVEL....................................................................................................82
6.12.5.2. Creating a MANUAL LEVEL.........................................................................................................83
6.12.5.3. Editing or Deleting a LEVEL.........................................................................................................84
6.12.6. Configuring LEVEL Status Blocks .......................................................................................................86
7. OPERATING THE M703E OVER THE SERIAL I/O PORTS.............................................. 87
7.1. Using the Analyser’s Communication Ports.................................................................................................87
7.1.1. RS-232 DTE and DCE Communication.................................................................................................87
7.1.2. COMM Port Default Settings and Connector Pin Assignments.............................................................88
7.1.3. COMM Port Baud Rate..........................................................................................................................90
7.1.4. COMM Port Communication Modes......................................................................................................91
7.1.5. COMM Port Testing ...............................................................................................................................93
iv 05744 Rev B